Axsail
SURVEY TEST METHODS · HULL AND STRUCTURE

Underwater hull inspection: diver, ROV or drone, what to check and how to record it

UPDATED 18 NOVEMBER 2026 · 5 SOURCES

Underwater hull inspection by diver or ROV: site and visibility limits, the checklist of hull, running gear and openings, and what the diver's report must show.

AT A GLANCE
Underwater hull inspection
MEASURES
Condition of the hull below the waterline, its openings and its running gear, seen by a diver or an ROV camera while the boat is afloat
TOOLS
A diver with lights and a camera, or an ROV; two-way communication to the surface; video and still photographs with a scale
WHEN TO USE
In-water surveys in lieu of a dry docking, insurers that accept a diver's report, damage checks after a grounding or contact, and checks between haul-outs
READ WITH
The last haul-out survey, the hull plans with their markings, and the owner's declaration of any contact since

An underwater hull inspection checks the hull, its openings and its running gear while the boat stays afloat, by a diver or a remotely operated vehicle (ROV) with the surveyor watching from the surface. For ships it's the in-water survey that can replace an alternate dry docking, and the rules for it, IACS UR Z3, the MCA's MGN 546 and Transport Canada's TP 11249, set out the method well. The same method works on a yacht or a workboat between haul-outs.

Diver, ROV or drone

Method Where it fits What the rules say
Diver with a helmet camera and comms Close work: clearances, feeling a bearing, opening a rope guard TP 11249 asks for a competent diver using closed circuit television with two-way communication the surveyor can monitor
ROV (underwater drone) Long runs of plating, repeat checks, sites where diving is unsafe MGN 546 accepts an ROV as an alternative to, or in addition to, divers
Diver and ROV together Larger hulls, or where a close look follows the camera pass Both count under MGN 546; the surveyor must be satisfied with the pictures either way

Deep Trekker, an ROV maker, says on its UWILD page that an ROV keeps the diver out from under the hull and lets you rehearse the inspection before the supervised one. It also cites ABS: where repairs to propellers, rudders, stern frames or sea valves are outstanding, dry docking may be the only option.

Site and visibility

  • Water: sheltered, with weak tidal streams and currents, per IACS UR Z3. MGN 546 puts the current at less than 0.5 knot and prefers the vessel at anchor.
  • Visibility: good enough to judge plating, appendages and welds. MGN 546 says to stop if it's generally below 5 metres, and to check visibility and scale during the survey.
  • Hull: clean before the dive. Fouling hides the defects you're looking for.
  • Safety: propellers, rudders and thrusters locked, pumps stopped, a permit to work. In the UK the Diving at Work Regulations apply; MGN 546 gives a minimum of 4 in the dive team as an example.
  • Stop rule: both MGN 546 and TP 11249 say to discontinue if the pictures or communications are no longer acceptable.

The checklist

MGN 546 and Deep Trekker's UWILD checklist cover the same ground:

Area What to look at
Hull plating or laminate Corrosion, distortion, indentations, cracks, weld seams, paint, fouling
Openings Every through-hull, sea chest, inlet and discharge, thruster tunnel, grating
Propellers Blades for dings, dents or bends, hubs, rope guards
Shafts and seals Stern bearing seal assembly and wear-down; P-brackets and A-frames
Rudder Pintles and gudgeons intact and secure, bearing clearance
Appendages Keel, bilge keels, stabiliser boxes, transducers
Protection Anodes and their fixings

Work in a fixed order, bow to stern down one side and back up the other, and say where you are as you go. MGN 546 asks the survey to cover the entire hull and its fittings before it counts in lieu of a dry docking, plus the hull above the waterline.

What the report must show

The diving company's report is cross-referenced to the video, photographs and annotated plans, per MGN 546. Deep Trekker adds that the start and end time of the dive are documented. TP 11249 asks for colour photographs or video of the shell openings and the rudder and shaft wear-down points, each with a scale. Anything that looks like damage is examined from inside too: MGN 546 warns against underestimating defects seen only from outside.

For surveyors

Whoever's on the surface already narrates the dive: the rules ask for two-way communication so the surveyor can direct the diver or the ROV. With Axsail that commentary becomes the report. The surveyor or ROV pilot talks through each area as the camera reaches it, stills from the camera go on the finding they belong to, and the draft follows the underwater hull inspection report template. For the rules on when an in-water survey can replace a haul-out, see in-water survey requirements and UWILD.

Findings to look for

Each page shows how the defect is found, what decides the grade and example findings written up at A, B and C.

UNDERWATER GEAR

Damaged propeller

How to inspect a propeller for bent blades, nicks, cracks and a spun hub, when to repair and when to replace, the repitch limits for bronze and stainless, repair costs for aluminium and stainless, and three example findings graded A, B and C.

How to find and write it up
UNDERWATER GEAR

Depleted anodes

When sacrificial anodes need replacing, zinc, aluminium or magnesium for your water, what anodes that aren't wasting mean, what a surveyor checks and three example findings graded A, B and C.

How to find and write it up
UNDERWATER GEAR

Worn cutless bearing

How a surveyor checks a cutless bearing for play, what 1/16 inch of movement means, what uneven wear says about alignment, what replacement involves and three example findings graded A, B and C.

How to find and write it up
UNDERWATER GEAR

Rudder bearing wear

How to check a rudder for bearing play and a wet or corroded rudder on the haul-out, what the thunk means, how often to drop the rudder to see the stock, and three example findings graded A, B and C.

How to find and write it up
UNDERWATER GEAR

Seized seacocks

Why a seacock that won't close is a safety finding, how surveyors check seacocks and through-hulls, the ABYC strength test a ball valve on a through-hull can fail, replacement costs and three example findings graded A, B and C.

How to find and write it up
HULL AND STRUCTURE

Osmotic blistering

What osmotic blistering is, how a surveyor tells it from paint blisters, which moisture readings matter, what treatment costs per foot and three example findings graded A, B and C.

How to find and write it up

Frequently asked

Can a diver or an ROV do an underwater hull inspection?

Either. The MCA's MGN 546 says a remotely operated vehicle may be used as an alternative to, or in addition to, divers, and IACS UR Z3 asks the classification society to be satisfied with how the divers or ROV find their position on the plating.

What visibility do you need for an underwater hull inspection?

Enough for the surveyor to judge plating, appendages and welds, per IACS UR Z3. The MCA's MGN 546 goes further: if visibility is generally below 5 metres, the survey should be discontinued.

What should an underwater hull inspection report include?

MGN 546 asks the diver to report on plating, weld seams, corrosion, distortion, indentations, cracks, paint, all hull openings and sea chests, propellers, seals, rudders and bearings, with the report cross-referenced to the video, photographs and plans.

Do insurers accept a diver's report for a boat left afloat?

Some do. American Modern accepts an in-water survey if the boat has had bottom maintenance in the past 24 months, shown by a work order or diver's report. Ask the insurer before you book.

Your full survey report, minutes after the walk-round

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More test methods

All test methods
HULL AND STRUCTURE

Ultrasonic thickness testing

Ultrasonic hull thickness testing on steel boats and narrowboats: gauge or A-scan, mill tolerance, wastage limits and the 4 mm insurance rule.

Read the method
ELECTRICAL AND GAS

Hull potential test

How to run a hull potential test with a silver/silver chloride reference electrode: setup, protection ranges by hull type and the shore power isolation check.

Read the method
HULL AND STRUCTURE

Percussion test (hammer sounding)

How surveyors sound a fibreglass hull for delamination: which hammer or coin to use, tapping every 2 to 3 inches, and telling a dull thud from a bulkhead.

Read the method
HULL AND STRUCTURE

Inclining experiment

What an inclining experiment is for, how it is run under the MCA and Red Ensign codes, the 8 weight movements and when a lightweight check will do.

Read the method
ENGINES AND MACHINERY

Diesel compression test

How to compression test a marine diesel: the kit, testing through injector or glow plug holes, typical readings and what low cylinders point to.

Read the method
ENGINES AND MACHINERY

Borescope engine inspection

How a borescope engine inspection works on a marine engine: access, piston at bottom centre, which optical tip to use, and how to record each cylinder.

Read the method

Report templates

FREE TEMPLATE · WORD

Underwater hull inspection

Free Word underwater hull inspection report template for diver or ROV surveys: dive conditions, hull checklist and example findings graded A, B and C.

Open template
FREE TEMPLATE · WORD

Out of water survey

A free Word template for an out of water boat survey report: the hull below the waterline, moisture readings, running gear and through-hulls, with example wording and example findings graded A, B and C.

Open template

Related guides

YACHT SURVEYS · 3 MIN

Out of water boat survey: what's checked below the waterline and when insurers want one

What a surveyor checks when the boat is hauled: blisters, moisture, delamination, keel, rudder, running gear, through-hulls and anodes, how long the short haul takes, and when an insurer accepts an in-water survey instead.