An underwater hull inspection report records what a diver or an ROV saw below the waterline while the boat stayed afloat. It needs everything an out of water report has, plus the dive conditions that decide how much the footage can show. This template follows the reporting points in the MCA's MGN 546 and IACS UR Z3, the rules for in-water surveys in lieu of dry docking, and works for a yacht or workboat between haul-outs too.
The report, section by section
Particulars
The vessel, the client, and who was in the water. IACS UR Z3 and the MCA's MGN 546 both expect the report to name the in-water survey firm and the surveyor who watched.
- Survey: client, insurer, class society or flag if it's an in-water survey in lieu of dry docking, date and place
- Vessel: name, make and model, HIN or IMO number, length overall, hull material, draft on the day
- Team: diving company or ROV operator, diver or pilot names, surveyor attending
- Method: diver with helmet camera and comms, ROV, or both
Inspected afloat at anchor in the bay, sheltered from the prevailing wind. Diver with helmet camera and hard-wire comms, surveyor on the tender monitoring video and audio.
Dive conditions
The conditions decide what the footage can show. MGN 546 says to stop if visibility is generally below 5 metres, and both MGN 546 and TP 11249 say to stop if pictures or communications become unacceptable. Record them so the reader can judge the findings.
- Current, tidal state and water depth under the keel
- Visibility at the start and at each check during the dive
- Hull cleanliness and whether it was cleaned before the dive
- Start and end time of the dive or ROV run
- Propellers, rudder and thrusters locked, pumps stopped, permit to work
Current under 0.3 knot, slack water. Visibility 7 to 8 metres throughout. Hull cleaned by diver the day before. Dive 10:05 to 11:20. Shaft locked and seawater pumps off, confirmed with the skipper before entry.
Scope and limitations
What the dive covered and what it couldn't. MGN 546 asks for the entire hull and its fittings to be covered before an in-water survey counts in lieu of dry docking, so list anything missed and why.
- Areas covered, in the order inspected
- Areas not inspected and the reason, such as fouling, low visibility or a fender against the quay
- Measurements taken, such as bearing clearances or ultrasonic thickness readings
- The owner's or master's declaration of any grounding or contact since the last haul-out
Hull below the waterline inspected bow to stern on the port side and back on starboard. The keel bottom was not inspected: the boat was too close to the seabed at low water. The owner declares no grounding or contact since the last haul-out.
Summary of recommendations
Every recommendation once, grouped by grade, with any item that needs a haul-out flagged as such.
- A, safety: fix before the boat goes back into service, or haul out for it
- B, 12 months: fix within about a year, or at the next haul-out
- C, routine: maintenance and notes
A1. Haul out to replace the cutless bearing, which shows play the diver could move by hand (finding 3.3).
Findings
Area by area, each with the video time stamp or still photo that shows it. MGN 546 asks the diver's report to be cross-referenced to the video, photographs and plans.
- Hull plating or laminate, paint, fouling, blisters, dents and repairs
- Every through-hull, inlet, discharge, sea chest and grating
- Keel and keel-to-hull joint, rudder, pintles and bearings
- Propeller blades, hub, shaft, P-bracket and cutless bearing, or the drive leg
- Anodes and transducers
Conclusion
The condition below the waterline as seen, and whether a haul-out is needed before the next one is due.
- The overall condition of the hull below the waterline
- Whether anything seen needs a haul-out or an internal check to confirm
The hull below the waterline is in fair condition. The cutless bearing needs replacing at a haul-out, and the dent at the forward port quarter should be checked from inside before the boat goes back to sea.
Surveyor's certification
Your statement, name, accreditation and signature, with the diving company's details beside yours.
- Statement of independence and who may rely on the report
- Name, accreditation and membership number of the surveyor, and the diving company
- Signature and date of issue
Example findings
Each finding says what the system is, where it is, what was found and what should be done, with a grade for how urgent it is. These are written the way Axsail writes them from what the surveyor says on board.
Diver could move the shaft by hand in the bearing, with visible play at the strut. Video 10:42.
Recommendation: Haul out and replace the cutless bearing before the boat goes back into service.
Dent about 150 mm across with paint scraped to bare laminate. No cracking seen on camera. Still photo 4.
Recommendation: Check the area from inside for cracking or delamination, and repair the laminate at the next haul-out.
Grating partly blocked with barnacles. Video 10:31.
Recommendation: Clear the grating and check the strainer.
About half wasted, fixings tight.
Recommendation: Replace at the next haul-out, or by diver within 3 months.
Using it on a dive
Keep the findings in the order you inspected, and give each one a video time stamp or a photo number so the reader can find it in the footage. MGN 546 asks for exactly that cross-reference. For the rules behind an in-water survey, see in-water survey requirements and UWILD; for how the dive itself is run, see underwater hull inspection.
With Axsail, the surveyor on the comms or the ROV pilot talks through each area as the camera reaches it. Stills taken from the footage go on the finding they belong to, and the draft fills these sections before you're back at the dock.