Axsail
SURVEY TEST METHODS · ENGINES AND MACHINERY

Borescope engine inspection: looking inside a marine engine's cylinders without taking it apart

UPDATED 17 NOVEMBER 2026 · 3 SOURCES

How a borescope engine inspection works on a marine engine: access, piston at bottom centre, which optical tip to use, and how to record each cylinder.

AT A GLANCE
Borescope engine inspection
MEASURES
Visual condition of cylinder walls, piston crown, valves and valve seats, through an access port
TOOLS
A videoscope with articulating tip, side view and direct view optical tips, a rigid sleeve, and a way to turn the engine by hand
WHEN TO USE
After a low compression reading, signs of water or coolant in a cylinder, or on an engine survey where the owner allows ports to be opened
READ WITH
Compression and oil analysis results, and the engine's hours and history

A borescope engine inspection puts a camera into each cylinder through an access port to see the cylinder walls, piston crown and valves without stripping the engine. Instrument maker Evident describes it as the step after readings and oil analysis, when those can't explain a problem. On a marine engine survey it usually follows a low compression test reading, to find out why that cylinder is low. The method below is from Evident and Waygate Technologies' guidance.

What it can show

Area What to look for, per Waygate and Evident
Cylinder walls Cross-hatching and scoring
Valves and seats Erosion and cracks; an articulating tip can look back at the valve
Cylinder head and casting Cracks between cylinders, seals and passageways
Piston crown and valve deck General condition, and marks that show orientation

How to run it

Evident's steps:

  1. Let the engine cool. Cylinders can still be hot after shutdown, which risks the scope and you.
  2. Prepare the scope. Fit the right optical tip, check the O-ring on the distal end, and clean the tip.
  3. Open the access ports for the cylinders you'll inspect.
  4. Insert through a rigid sleeve. It steadies the image and keeps the probe off the cylinder walls and out of the oil.
  5. Bring the piston to bottom centre. Watch the screen while turning the engine by hand. Following the firing order saves time.
  6. Orient the image. Rotate the probe so 12 o'clock is at the top of the screen, using marks on the piston crown as reference.
  7. Survey with a side view tip across walls, piston, valve deck and valves, then switch to a direct view tip for detail on anything suspect.
  8. Release the articulation lock and withdraw slowly. Repeat for each cylinder.

Lubricant degrades the image, so keep isopropyl alcohol and cotton buds to clean the tip when it blurs.

Recording it

Evident recommends saving each cylinder's images in its own folder, so file names carry the cylinder and the report is easier to build. The finished borescope report becomes the reference for the next inspection.

For surveyors

Opening injector or glow plug ports is invasive, so agree it with the owner first and note who opened them. Record each cylinder with its images and what you saw, alongside the compression readings for the same cylinder. With Axsail, say "cylinder 3, vertical scoring on the thrust side, cross-hatch gone in the upper third" as you capture the frame, and it goes into the engine survey report next to that cylinder's compression figure.

Findings to look for

Each page shows how the defect is found, what decides the grade and example findings written up at A, B and C.

ENGINE AND FUEL

Exhaust smoke

What white, blue and black smoke from a marine diesel point to, when smoke is normal, how to watch the exhaust on a sea trial, and three example findings graded A, B and C.

How to find and write it up
ENGINE AND FUEL

Engine overheating

Why marine diesels overheat, chronic against acute overheating, the order to check the cooling system in, the temperature test for a blocked exhaust elbow, what a surveyor checks and three example findings graded A, B and C.

How to find and write it up

Frequently asked

What can a borescope show inside a diesel engine?

Waygate lists the cylinder walls, where cross-hatching and scoring can be judged, valve seats for erosion and cracks, and the cylinder head for cracks between cylinders. Evident adds the piston crown and valve deck.

Where should the piston be for a borescope inspection?

Evident says cylinder inspection must be done with the piston at the very bottom of the cylinder, bottom centre, to see the largest extent of the walls. Watch the screen while turning the engine by hand until it's there.

Should the engine be cold for a borescope inspection?

Evident warns that cylinders may still be hot depending on how long ago the engine was shut down, and says to let it cool to avoid damage to the scope and injury.

How does a borescope fit with other engine tests?

Evident describes borescope work as one condition monitoring technique alongside instrument readings and used oil analysis, used when those non-invasive methods can't give enough information.

Your full survey report, minutes after the walk-round

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More test methods

All test methods
ENGINES AND MACHINERY

Diesel compression test

How to compression test a marine diesel: the kit, testing through injector or glow plug holes, typical readings and what low cylinders point to.

Read the method
HULL AND STRUCTURE

Percussion test (hammer sounding)

How surveyors sound a fibreglass hull for delamination: which hammer or coin to use, tapping every 2 to 3 inches, and telling a dull thud from a bulkhead.

Read the method
HULL AND STRUCTURE

Ultrasonic thickness testing

Ultrasonic hull thickness testing on steel boats and narrowboats: gauge or A-scan, mill tolerance, wastage limits and the 4 mm insurance rule.

Read the method
HULL AND STRUCTURE

Inclining experiment

What an inclining experiment is for, how it is run under the MCA and Red Ensign codes, the 8 weight movements and when a lightweight check will do.

Read the method
HULL AND STRUCTURE

Underwater hull inspection

Underwater hull inspection by diver or ROV: site and visibility limits, the checklist of hull, running gear and openings, and what the diver's report must show.

Read the method
ELECTRICAL AND GAS

Boat battery test

How to test a boat battery, from Trojan, Crown and Lifeline: rested voltage, hydrometer readings, load tests and a full capacity test, and which to trust.

Read the method

Known engine problems

HOURS AND CONDITION

Boat engine hours

How many hours boat engines last before a major overhaul, gas and diesel, average hours per year, and why service records matter more than the hour meter.

What to check
DIESEL ENGINES

Yanmar GM series

Known problems on Yanmar GM series sailboat diesels and where to look: the exhaust elbow that corrodes from the inside and sends water back into the cylinders, valve seats and compression, the air filter, soft engine mounts, and fuel knock.

What to check

Report templates

FREE TEMPLATE · WORD

Engine survey

A free Word template for a marine engine survey report: engine records, visual inspection, cold start, readings under load, oil analysis and conclusions, with example findings graded A, B and C.

Open template