Axsail
SURVEY TEST METHODS · ELECTRICAL AND GAS

Boat battery testing: voltage, hydrometer, load and capacity tests, and which one to trust

UPDATED 17 NOVEMBER 2026 · 3 SOURCES

How to test a boat battery, from Trojan, Crown and Lifeline: rested voltage, hydrometer readings, load tests and a full capacity test, and which to trust.

AT A GLANCE
Boat battery test
MEASURES
State of charge (voltage, specific gravity) and remaining capacity (discharge test)
TOOLS
DC voltmeter, hydrometer for flooded batteries, a load tester or conductance tester, an amp-hour meter for a capacity test
WHEN TO USE
Every survey where batteries are older than a few seasons, or when they don't hold a charge
READ WITH
The maker's state of charge table and the battery's rated capacity

Testing a boat battery properly takes more than a voltmeter. Trojan's maintenance guide checks state of charge two ways: a rested open-circuit voltage and, on flooded batteries, a hydrometer reading in every cell. Lifeline adds that a quick load or conductance test doesn't reliably show how much capacity is left, and recommends a full discharge test for that. The steps below are from both makers' own guidance.

Start with an inspection

Trojan's checklist before any test: look for cracks in the case, dirt or corrosion on the top and posts, fluid on or around the battery, which means electrolyte leaking, and loose or damaged cables. Leaking batteries must be replaced. Tighten connections to the specified torque, but not over, since Trojan warns that over-tightening can break or melt a post.

Open-circuit voltage

  1. Leave the battery idle, no charging or discharging, for at least 6 hours and preferably 24 (Trojan).
  2. Disconnect all loads.
  3. Measure with a DC voltmeter and read the state of charge from the maker's table.
  4. Charge it if it's at 70% or below.

Lifeline puts a full AGM at 2.17 volts per cell or more after at least 4 hours' rest, 13.0 V on a 12 V battery. The battery state of charge table converts voltage for flooded and AGM batteries.

Hydrometer test, flooded batteries only

Trojan's procedure:

  1. Don't add water before testing.
  2. Fill and drain the hydrometer two to four times, then draw enough electrolyte to float the float.
  3. Read, record, and return the sample to the same cell. Test every cell.
  4. Correct to 80°F: add 0.004 per 10°F above, subtract 0.004 per 10°F below.

A fully charged Trojan cell reads 1.277, plus or minus 0.007. If one reads low, charge, then equalize and test again. Still low points to age, long storage flat, lost electrolyte or a failing cell, and Trojan says that battery should go to a specialist or be retired.

Load test and capacity test

Test What it tells you Lifeline's view
Conductance tester A quick health read Useful for a quick check
Load test with a real draw Whether voltage holds under load Short tests aren't reliable for actual capacity
Full discharge with an amp-hour meter Remaining capacity against the rating The test to use before replacing a battery

Crown Battery's load test, for batteries with a CCA rating: charge first, never load test below 75% state of charge, then apply half the CCA rating for 15 seconds and compare the voltage with the minimum. On flooded batteries Crown says to replace a battery whose cells differ by more than 50 points on the hydrometer.

Lifeline lists signs a battery needs replacing: voltage dropping under light load, not holding a charge after a full cycle, a failed load test, or an age over 5 to 7 years.

For surveyors

A survey rarely has time for a full capacity test, so record what you can stand behind: the rested voltage, specific gravity per cell on flooded batteries, the date codes, and a load or conductance result labelled as such. With Axsail, say "house bank, two flooded, rested 12.4 V, cell 4 reads 1.190" and it becomes a graded finding next to the battery age guidance.

Findings to look for

Each page shows how the defect is found, what decides the grade and example findings written up at A, B and C.

ELECTRICAL

Old batteries

How to read a battery's age from its date code, how long AGM batteries are expected to last, the resting voltage and load test a battery maker gives, the signs a bank is worn out, and three example findings graded A, B and C.

How to find and write it up
ELECTRICAL

Unsecured batteries

What ABYC E-10 asks of battery installations, why a loose battery is a safety finding, boxes versus straps, insulated terminals and three example findings graded A, B and C.

How to find and write it up

Frequently asked

Is a load test enough to condemn a boat battery?

Lifeline says short-duration load tests and impedance or conductance measurements aren't reliable for the battery's actual capacity. For serious testing it recommends a full discharge and recharge cycle with an accurate amp-hour meter.

How long should a battery rest before a voltage test?

Trojan says at least 6 hours, preferably 24, with no charging or discharging. Lifeline says an AGM rested at least 4 hours reads 2.17 volts per cell or more when full, 13.0 V on a 12 V battery.

What should a hydrometer read on a charged battery?

Trojan's factory specification for a fully charged flooded battery is 1.277, plus or minus 0.007, corrected to 80°F. Add 0.004 for every 10°F above, subtract 0.004 for every 10°F below.

What does a low specific gravity reading mean after charging?

Trojan says to charge fully, then equalize and re-test. If a cell still reads low, the battery may be old, left discharged too long, have lost electrolyte, or have a failing cell, and should go to a specialist or be retired.

Your full survey report, minutes after the walk-round

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More test methods

All test methods
ELECTRICAL AND GAS

LPG gas leak test

How a boat's LPG system is checked for leaks: the test point or bubble detector the Boat Safety Scheme requires, the tightness test and regulator lock-up.

Read the method
ELECTRICAL AND GAS

Hull potential test

How to run a hull potential test with a silver/silver chloride reference electrode: setup, protection ranges by hull type and the shore power isolation check.

Read the method
ELECTRICAL AND GAS

Thermal imaging

How surveyors use a thermal camera on a boat: hot electrical connections, cooling faults and active thermography for wet core, with its limits.

Read the method
HULL AND STRUCTURE

Percussion test (hammer sounding)

How surveyors sound a fibreglass hull for delamination: which hammer or coin to use, tapping every 2 to 3 inches, and telling a dull thud from a bulkhead.

Read the method
HULL AND STRUCTURE

Ultrasonic thickness testing

Ultrasonic hull thickness testing on steel boats and narrowboats: gauge or A-scan, mill tolerance, wastage limits and the 4 mm insurance rule.

Read the method
HULL AND STRUCTURE

Inclining experiment

What an inclining experiment is for, how it is run under the MCA and Red Ensign codes, the 8 weight movements and when a lightweight check will do.

Read the method

Standards to check against

ABYC E-10

Storage Batteries

What ABYC E-10 asks of battery installations on boats, the one inch movement test, terminal protection, containment and ventilation, what a surveyor checks and how to cite E-10 in a finding.

What surveyors check

Report templates

FREE TEMPLATE · WORD

Survey findings report

A free Word template for a marine survey findings report: a short report of findings and recommendations by grade, the status of earlier recommendations, and example findings written out in full.

Open template