Axsail
SURVEY TEST METHODS · HULL AND STRUCTURE

Inclining experiment: how a small vessel's lightship weight and centre of gravity are found

UPDATED 17 NOVEMBER 2026 · 3 SOURCES

What an inclining experiment is for, how it is run under the MCA and Red Ensign codes, the 8 weight movements and when a lightweight check will do.

AT A GLANCE
Inclining experiment
MEASURES
Lightship weight and the vertical and longitudinal centres of gravity, from the heel produced by moving known weights
TOOLS
Known test weights, pendulums or a calibrated electronic inclinometer, draught readings, and the procedure the Administration or certifying authority approves
WHEN TO USE
New coded vessels needing a stability booklet, after major modifications, and when a lightweight check shows too large a change
READ WITH
The code's stability chapter and the approved stability information booklet

An inclining experiment finds a vessel's lightship weight and centre of gravity by moving known weights across the deck and measuring the heel. Those figures are the starting point for every stability calculation, so the codes require one before a stability booklet is approved. The Workboat Code Edition 3 asks for at least 8 weight movements, and the Red Ensign Yacht Code requires it to be done to an approved standard in the Administration's presence. The rules below are from those codes.

When the codes require one

Code Requirement
Workboat Code Edition 3, 12B.3.1 Lightship weight, VCG and LCG of a monohull needing an approved stability booklet come from an inclining experiment, with at least 8 weight movements
Sport or Pleasure Vessel Code, section 12 The centre of gravity is established by an inclining experiment, with GZ curves for loaded departure and arrival; production boats can use a sister vessel's result, corrected for outfit
REG Yacht Code Part A, chapter 11 Lightship weight, KG and LCG from an inclining experiment to an approved standard, in the Administration's presence, with the report approved before use

Running it

The Workboat Code points to the MCA's Instructions for the Guidance of Surveyors on Load Line, MSIS 1 Part 6, for the procedure. The codes add:

  • at least 8 weight movements
  • a calibrated electronic inclinometer may replace the second pendulum, with readings recorded
  • any deviation from MSIS 1 in pendulums or repetitions agreed with the certifying authority
  • for yachts under REG Part A, the inclining report and lightship particulars approved by the Administration before use

REG Part A refers large commercial yachts to the MCA's guidance notes for carrying out an inclining test.

Multihulls and margins

The Workboat Code says an inclining experiment may not work where the VCG is less than a third of the GM, which covers most multihulls. Their LCG comes from a displacement check or weighing with two gauges, and the VCG from an accurate weight estimate with a margin, never below main deck level. A margin for growth of up to 5% of lightship weight may be included, but not used to raise cargo deadweight.

What the result feeds

GZ curves are produced for loaded departure with 100% consumables, loaded arrival with 10%, expected service conditions, and lifting conditions where relevant. For a monohull under the Workboat Code they must show:

Criterion Minimum
Area under GZ to 30° 0.055 metre-radians
Area under GZ to 40°, or downflooding 0.09 metre-radians
Area between 30° and 40° 0.03 metre-radians
GZ at 30° or more 0.20 m
Angle of maximum GZ At least 25°
Initial GM after free surface 0.35 m

Lightweight checks instead

  • Sister ships. Under the Workboat Code, a sister built within five years can use a lightweight check if lightship displacement is within 2% and LCG within 1% of the lead vessel; outside those limits, an inclining test is needed.
  • Large yachts. REG Part A requires a lightweight check every five years unless no major change can be shown, and treats a 2% change in lightship weight, 1% in LCG or a 0.25% rise in VCG as major.
  • Modified boats. Under the Workboat Code, an owner who modifies a vessel informs the certifying authority, which may carry out a lightship or freeboard check.
  • Older coded boats. Under the Sport or Pleasure Vessel Code, if stability information hasn't been reassessed within 20 years, the certifying authority does a lightship or freeboard check at the next renewal, with a full reassessment if the data has changed more than 5%.

For surveyors

Record the weights, their movements, the pendulum or inclinometer readings, draughts and density of the water, and everything aboard that isn't part of lightship. With Axsail, dictate each movement and reading as it happens, "movement 3, 250 kilos to port, 3.1 metres, pendulum 42 millimetres", and the record comes out as a table for the stability report.

Frequently asked

What is the purpose of an inclining experiment?

To find a vessel's lightship weight and the position of its centre of gravity, vertical and longitudinal, which every stability calculation and the stability booklet depend on. The Workboat Code Edition 3 requires it for monohulls that need an approved stability information booklet.

How many weight movements does an inclining experiment need?

The Workboat Code Edition 3 requires at least 8 weight movements. A calibrated electronic inclinometer is an acceptable alternative to the second pendulum, with the procedure in the MCA's MSIS 1 Part 6 as the guideline.

Does a catamaran need an inclining experiment?

The Workboat Code says an inclining experiment may not give satisfactory results where the VCG is less than a third of the GM, such as multihulls. Their LCG comes from a displacement check or weighing, and the VCG from a weight estimate with a margin, never below main deck level.

How often is a lightweight check needed on a large yacht?

REG Yacht Code Part A requires a lightweight check every five years unless it can be clearly shown that no major change has occurred.

Your full survey report, minutes after the walk-round

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More test methods

All test methods
HULL AND STRUCTURE

Percussion test (hammer sounding)

How surveyors sound a fibreglass hull for delamination: which hammer or coin to use, tapping every 2 to 3 inches, and telling a dull thud from a bulkhead.

Read the method
HULL AND STRUCTURE

Ultrasonic thickness testing

Ultrasonic hull thickness testing on steel boats and narrowboats: gauge or A-scan, mill tolerance, wastage limits and the 4 mm insurance rule.

Read the method
HULL AND STRUCTURE

Underwater hull inspection

Underwater hull inspection by diver or ROV: site and visibility limits, the checklist of hull, running gear and openings, and what the diver's report must show.

Read the method
ENGINES AND MACHINERY

Diesel compression test

How to compression test a marine diesel: the kit, testing through injector or glow plug holes, typical readings and what low cylinders point to.

Read the method
ENGINES AND MACHINERY

Borescope engine inspection

How a borescope engine inspection works on a marine engine: access, piston at bottom centre, which optical tip to use, and how to record each cylinder.

Read the method
ELECTRICAL AND GAS

Boat battery test

How to test a boat battery, from Trojan, Crown and Lifeline: rested voltage, hydrometer readings, load tests and a full capacity test, and which to trust.

Read the method

Standards to check against

ISO 12217

Small craft, Stability and buoyancy assessment and categorization

What the RCD design categories A, B, C and D mean in wind force and wave height, how ISO 12217 stability assessment sets them, why load changes the category, and how surveyors use them in a report.

What surveyors check
MCA SPORT OR PLEASURE VESSEL CODE

The safety of small vessels in commercial use for sport or pleasure: a code of practice

The MCA code for small UK vessels in commercial use for sport or pleasure: which boats it covers, the codes it replaces, area categories 0 to 6, the five-year certificate, the examination cycle and the SCV2 record.

What surveyors check

Report templates

FREE TEMPLATE · WORD

New build survey

A free Word template for a new build or build stage survey report: progress against the specification, inspection by stage, compliance, the punch list and acceptance trials, with example findings graded A, B and C.

Open template