Axsail
SURVEY TEST METHODS · ENGINES AND MACHINERY

Compression test on a diesel engine: how to do it on a boat and what the readings mean

UPDATED 17 NOVEMBER 2026 · 3 SOURCES

How to compression test a marine diesel: the kit, testing through injector or glow plug holes, typical readings and what low cylinders point to.

AT A GLANCE
Diesel compression test
MEASURES
Peak pressure each cylinder builds while the engine is cranked without starting
TOOLS
A diesel compression gauge rated to the engine's pressures, with adaptors for the injector or glow plug holes
WHEN TO USE
Hard starting, smoke, low power or blow-by on a pre-purchase or engine survey
READ WITH
The engine maker's figure from the service manual, and the spread between cylinders

A compression test on a diesel engine measures how much pressure each cylinder builds when the engine is cranked without firing. It needs a gauge rated for diesel pressures, fitted through the injector or glow plug holes one cylinder at a time. Canadian Boating's marine mechanic puts a healthy diesel at about 300 to 500 psi, and Yachting's rule is that cylinders should read within about 10% of each other. The engine maker's service manual figure is the one a reading is judged against.

Before you start

48 North's marine diesel mechanic starts without a gauge. With the engine running, take off the oil filler cap: crankcase pressure should be atmospheric, so puffing against your hand means compression is getting past the rings or valves. Feeling at the dipstick tube as well helps tell the bottom end from the top. The article adds that most signs of poor compression, such as hard starting, show up well before the gauge comes out.

How to run the test

Canadian Boating's steps, from Andrew McDonald of Lakeside Marine Services:

  1. Disable the engine so it can't start. Ask a marine technician if you're not sure how.
  2. Choose the access point: the injectors or the glow plugs, whichever is easier to reach and fits your adaptors.
  3. One cylinder at a time, remove the injector or glow plug, fit the adaptor to the maker's instructions and connect the gauge.
  4. Crank the engine with the starter, or turn it by hand, for 5 to 10 seconds, with any decompression lever in the right position.
  5. Record the reading, refit, and move to the next cylinder.

Reading the results

Result What Canadian Boating says it points to
All cylinders even and in the normal range Healthy compression
One cylinder low That cylinder's walls, piston, rings or valves
Two adjacent cylinders low Head gasket failing between them
All cylinders low General wear in valves, gaskets and rings; check the oil too
A cylinder reading high Debris, water or carbon build-up in the cylinder

Canadian Boating suggests cylinders should be within about 10 psi of each other, and Yachting's rule is a spread within about 10%. Use the compression test results calculator to work out the spread and flag low cylinders. A borescope inspection through the same port shows why a cylinder is low.

Why marine diesels lose compression

48 North points to two common causes on recreational boats. Wet exhausts and salt air corrode valve seats, making engines hard to start. Long idling or running without load builds soot and carbon that wear the cylinder walls, and the article recommends running at about 80% load. Engines without glow plugs, such as the Yanmar GM series, show compression loss as hard cold starting first.

For surveyors

Write down every reading with its unit, whether the engine was warm or cold, and which holes you tested through. With Axsail, say "compression, warm, through the injectors: 1, 420; 2, 415; 3, 360 psi" and it goes into the engine survey report as a table, with cylinder 3 flagged.

Findings to look for

Each page shows how the defect is found, what decides the grade and example findings written up at A, B and C.

ENGINE AND FUEL

Exhaust smoke

What white, blue and black smoke from a marine diesel point to, when smoke is normal, how to watch the exhaust on a sea trial, and three example findings graded A, B and C.

How to find and write it up
ENGINE AND FUEL

Exhaust elbow corrosion

Why marine diesel mixing elbows corrode from the inside, the signs a surveyor looks for, how long they last, what replacement costs and three example findings graded A, B and C.

How to find and write it up

Frequently asked

Can you do a compression test on a diesel engine?

Yes, with a gauge built for diesel pressures and adaptors for the injector or glow plug holes. Canadian Boating's marine mechanic says to disable the engine, test one cylinder at a time, and crank for 5 to 10 seconds per reading.

What should diesel compression be?

Canadian Boating gives 300 to 500 psi as the usual range for a diesel, against 110 to 150 psi for a petrol engine. The engine maker's service manual figure is the one to judge against, and Yachting says cylinders should read within about 10% of each other.

What does low compression on two cylinders next to each other mean?

Canadian Boating says two adjacent low cylinders point to a head gasket failing between them. One low cylinder points at that cylinder's rings or valves; all of them low points to general wear.

Is there a quick check for compression loss without a gauge?

A marine diesel mechanic writing in 48 North removes the oil filler cap with the engine running: crankcase pressure should be atmospheric, so puffing against the hand means compression is leaking past the rings or valves. Checking at the dipstick helps separate the bottom end from the top.

Your full survey report, minutes after the walk-round

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More test methods

All test methods
ENGINES AND MACHINERY

Borescope engine inspection

How a borescope engine inspection works on a marine engine: access, piston at bottom centre, which optical tip to use, and how to record each cylinder.

Read the method
HULL AND STRUCTURE

Percussion test (hammer sounding)

How surveyors sound a fibreglass hull for delamination: which hammer or coin to use, tapping every 2 to 3 inches, and telling a dull thud from a bulkhead.

Read the method
HULL AND STRUCTURE

Ultrasonic thickness testing

Ultrasonic hull thickness testing on steel boats and narrowboats: gauge or A-scan, mill tolerance, wastage limits and the 4 mm insurance rule.

Read the method
HULL AND STRUCTURE

Inclining experiment

What an inclining experiment is for, how it is run under the MCA and Red Ensign codes, the 8 weight movements and when a lightweight check will do.

Read the method
HULL AND STRUCTURE

Underwater hull inspection

Underwater hull inspection by diver or ROV: site and visibility limits, the checklist of hull, running gear and openings, and what the diver's report must show.

Read the method
ELECTRICAL AND GAS

Boat battery test

How to test a boat battery, from Trojan, Crown and Lifeline: rested voltage, hydrometer readings, load tests and a full capacity test, and which to trust.

Read the method

Known engine problems

DIESEL ENGINES

Yanmar GM series

Known problems on Yanmar GM series sailboat diesels and where to look: the exhaust elbow that corrodes from the inside and sends water back into the cylinders, valve seats and compression, the air filter, soft engine mounts, and fuel knock.

What to check
DIESEL ENGINES

Volvo Penta D2

The known weak point on Volvo Penta D2 sailboat and small motorboat diesels: galvanic corrosion where the steel exhaust elbow meets the aluminium heat exchanger, which can leak exhaust into the boat. Where to look and how to write it up.

What to check

Report templates

FREE TEMPLATE · WORD

Engine survey

A free Word template for a marine engine survey report: engine records, visual inspection, cold start, readings under load, oil analysis and conclusions, with example findings graded A, B and C.

Open template

Related guides

INSPECTION CHECKLISTS · 4 MIN

Marine engine survey: what's checked, what it costs and a checklist

What a marine engine survey includes: oil analysis, compression test, sea trial under load and temperature readings, who does it, what it costs per engine, and a checklist for diesel and outboard engines.