Axsail
FAULT CODES · ONBOARD SYSTEMS

Dometic marine air conditioner fault codes: HPF, LPF, ASF, LAC, PLF and FIL, and how to clear a lockout

UPDATED 16 NOVEMBER 2026 · 3 FINDINGS · 2 SOURCES

Dometic marine air conditioner fault codes from Dometic's manuals: HPF, LPF, ASF, LAC, PLF and FIL, the failsafe levels and the lockout reset.

AT A GLANCE
Dometic marine air conditioning
MAKER
Dometic
COVERS
MCS6, MCS12 and MCS16 marine climate systems with the digital display, and DX systems with the Smart Touch Cabin Control, which shows the same faults in words
WHERE THE CODE SHOWS
As a three-letter code on the display panel, or as a fault message with help text on a Smart Touch screen
CHECK FIRST
Seawater flow: the seacock, the strainer, the pump and a steady stream from the overboard discharge

Dometic marine air conditioner fault codes are three-letter codes on the display: HPF for high pressure, LPF for low pressure, ASF for a failed air sensor, LAC for low AC voltage, PLF for an overheated condenser coil and FIL for a filter due for cleaning. In cooling, Dometic's troubleshooting table traces HPF to seawater flow. The codes below are from Dometic's manual for the MCS6, MCS12 and MCS16 marine climate systems, and the Smart Touch Cabin Control shows the same faults as text.

The fault codes

Code Meaning What Dometic says to check
HPF High Freon pressure Cooling: seawater flow, a plugged strainer or intake, a closed seacock, a kinked hose, the pump and its breaker. Heating: blocked return air, a dirty filter, crushed ducting
LPF Low Freon pressure Low seawater or return air temperatures, or loss of refrigerant. Check for oil leaks and call a technician
ASF Air sensor fault The face plate air sensor, the alternate air sensor, the display cable and its sockets
LAC Low AC voltage, if enabled The supply voltage with a multimeter, and that the voltage setting matches the reading
PLF Condenser coil too hot, if enabled Water flow to the unit and a fouled condenser, then the water sensor and its socket
FIL Filter needs replacing, if enabled Replace or clean the filter and reset the filter timer

HPF isn't shown and doesn't cause a lockout in heat mode. LPF has a 10 minute shutdown delay. On the Smart Touch, the low-pressure fault has a three-minute shutdown delay and the seawater low temperature limit fault shows when the seawater drops below 4 °C (40 °F).

Failsafe levels and lockout

The failsafe level sets which faults are detected and shown, and when the system locks out:

Level What happens
0 Only ASF is detected and shown
1 All faults detected but not shown. The system stops for 2 minutes or until the fault clears
2 Faults detected and shown, same 2 minute stop
3 As level 2, plus a lockout after four consecutive HPF or LPF faults

To clear a lockout, press the power button once for off and again for on. Dometic recommends the Smart Touch's no-detection level only for initial start-up and troubleshooting, and newer display software returns to full detection after five minutes.

Seawater and the condenser

Dometic's maintenance section asks owners to clean the strainer basket regularly, check the overboard discharge for a steady stream, check the intake scoop and keep hoses free of loops and kinks. Marine growth and scale in the condenser coil block water flow and heat transfer, which leads to HPF and PLF. The manual also asks for the unit to be run in heat for a few seconds once a month to keep the reversing valve free.

For surveyors

Run the air conditioning in cooling at the dock and watch the discharge. A weak stream with HPF on the display is a seawater circuit finding: seacock, strainer, pump or a fouled coil. Look at the seized seacocks and raw water pump leak findings. With Axsail, say "saloon aircon, HPF after 4 minutes in cool, discharge trickling, strainer half full of weed" and it's written up in the systems section.

Findings to look for on Dometic marine air conditioning

Each page shows how the defect is found, what decides the grade and example findings written up at A, B and C.

UNDERWATER GEAR

Seized seacocks

Why a seacock that won't close is a safety finding, how surveyors check seacocks and through-hulls, the ABYC strength test a ball valve on a through-hull can fail, replacement costs and three example findings graded A, B and C.

How to find and write it up
ENGINE AND FUEL

Raw water pump leak

What water from a raw water pump's weep hole means, how impellers fail, what a surveyor checks on the engine's cooling water pump, what a rebuild involves and three example findings graded A, B and C.

How to find and write it up
ELECTRICAL

Overheated shore power inlet

Why shore power inlets and cord ends overheat and burn, the infrared temperature check a former ABYC technical VP recommends, what to look for behind the inlet, and three example findings graded A, B and C.

How to find and write it up

Frequently asked

What does HPF mean on a Dometic marine air conditioner?

High Freon pressure. In cooling, Dometic's manual says the high-pressure switch opens because of poor seawater flow: a plugged strainer or intake, a closed seacock, a kinked hose or a pump that isn't running. In heating it's poor airflow. HPF isn't shown and doesn't cause a lockout in heat mode.

What does LPF mean on a Dometic air conditioner?

Low Freon pressure. The low-pressure switch has opened because of low seawater or low return air temperatures, or because of a loss of refrigerant. It has a 10 minute shutdown delay. Check for refrigerant oil leaks and call a service technician if it keeps happening.

How do I reset a Dometic marine air conditioner lockout?

At failsafe level 3, the system locks out after four consecutive HPF or LPF faults. Dometic's manual says to press the power button once to switch it off, then press it again to switch it on. Fix the seawater flow or airflow first, or it will lock out again.

What does ASF mean on a Dometic air conditioner?

Air sensor fault: the face plate air sensor, the alternate air sensor or the display cable has failed, or the socket in the display head or circuit board is damaged. It's the only fault detected at failsafe level 0.

Your full survey report, minutes after the walk-round

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More fault codes

All fault codes
ONBOARD SYSTEMS

Secop (Danfoss) BD35F and BD50F fridge compressors

Boat fridge compressor error codes for the Secop (formerly Danfoss) BD35F and BD50F from Secop's own instructions: what 1 to 6 LED flashes mean and what to check.

Look up a code
ONBOARD SYSTEMS

Sleipner Side-Power thrusters

Side-Power thruster error codes from Sleipner's legacy fault code list: motor overcurrent, overtemp, low voltage, IPC error, fuse blown and the retract faults.

Look up a code
ONBOARD SYSTEMS

Vetus DBPPJA thruster panel

Vetus bow thruster error codes on the DBPPJA proportional joystick panel, from Vetus's manual: overheated, overloaded, limiting, low supply and network faults.

Look up a code
ONBOARD SYSTEMS

Schenker ZEN watermakers

Schenker watermaker alarms on the ZEN touch panel, from Schenker's manual: System blocked, Control cable, Bad water quality, the bypass warnings and the valve reset.

Look up a code
ENGINES AND OUTBOARDS

Honda BF115 to BF250 outboards

Honda outboard alarm codes from Honda's owner's manuals: the ACG, malfunction, oil pressure and overheat indicators, each buzzer pattern and what to do.

Look up a code
ENGINES AND OUTBOARDS

Tohatsu MFS 75A to 115A outboards

Tohatsu outboard warning codes from Tohatsu's owner's manual for the MFS 75A, 90A and 115A: each buzzer and lamp pattern with its remedy, and the ESG speed limits.

Look up a code

Standards to check against

ABYC E-11

AC and DC Electrical Systems on Boats

What ABYC E-11 covers on a boat's AC and DC systems, the rules surveyors check most often, from the 7 inch battery fuse rule to the reverse polarity indicator, and how to cite E-11 in a finding.

What surveyors check

Report templates

FREE TEMPLATE · WORD

Sea trial report

A free Word template for a sea trial report: conditions and load, checks before departure, engine readings at each speed, systems tested under way, the engine room after the run, and example findings.

Open template