Axsail
FAULT CODES · ENGINES AND OUTBOARDS

Tohatsu outboard warning codes: what the buzzer, warning lamp and ESG speed limit mean on an MFS 75A to 115A

UPDATED 16 NOVEMBER 2026 · 3 FINDINGS · 1 SOURCES

Tohatsu outboard warning codes from Tohatsu's owner's manual for the MFS 75A, 90A and 115A: each buzzer and lamp pattern with its remedy, and the ESG speed limits.

AT A GLANCE
Tohatsu MFS 75A to 115A outboards
MAKER
Tohatsu
COVERS
MFS 75A, MFS 90A and MFS 115A four-stroke outboards, remote control models
WHERE THE CODE SHOWS
On the warning buzzer in the remote control and the warning lamp in the tachometer, with the engine's speed limited by the ESG
CHECK FIRST
Water from the cooling water check port, then the engine oil level and the propeller

Tohatsu outboard warning codes on the MFS 75A, 90A and 115A combine a buzzer, a warning lamp and the ESG, the Electronic Safety Governor that limits engine speed. A continuous buzzer means the ESG is cutting speed to protect the engine, from over-revving or from an oil or temperature problem. A flashing lamp on its own means a sensor or electrical fault. The patterns below are from Tohatsu's owner's manual for these models.

Warning patterns

Buzzer Warning lamp ESG Fault Remedy
Continuous On Normal test when the key is turned on
Continuous High speed ESG Engine speed above the maximum 1
Continuous On Low speed ESG Low oil pressure 2
Continuous Low speed ESG Engine temperature high 3
Continuous Flashing Low speed ESG, 1,800 rpm Engine temperature abnormally high 3
None Flashing Low speed ESG Engine temperature or MAP sensor fault, or battery overcharge 4
None Flashing Other sensor or electrical fault 4
None 1 second on, 9 off Oil change reminder, every 100 hours 5
One beep Lowest idle speed set, 650 rpm
Two beeps Highest idle speed set, 850 rpm

For low oil pressure, the buzzer and lamp stay on until the engine is stopped, which is what resets the warning system.

Remedies

No. What Tohatsu says to do
1 Throttle back below half, move to a safe place and stop. Check the propeller for bent or damaged blades. If it happens again with a new propeller, consult a dealer
2 Move to a safe place and stop. Check the oil level and top up. Consult a dealer if the level is too low or too high
3 Move to a safe place, check water from the cooling water check port at idle, then stop. Clear anything on the gear case or propeller. No water: consult a dealer
4 Consult an authorised dealer
5 Change the engine oil and reset the indicator

The ESG speed limits

The high speed ESG stops the engine over-revving when the load drops suddenly, holding it under 6,000 rpm. The low speed ESG protects the engine from cooling water, oil pressure and sensor problems by cutting fuel, holding it under 1,800 or 2,800 rpm. At key-on, the warning lamps should light with the buzzer and then go out, according to the pre-start checks in the manual.

For surveyors

On the sea trial, check the key-on test, a steady stream from the cooling water check port and full revs without the high speed ESG cutting in. An over-rev warning points to the propeller first, so look at the blades as in the propeller damage finding. With Axsail, say "Tohatsu MFS 90, continuous buzzer and lamp flashing at cruise, tell-tale weak" and it goes into the sea trial report.

Findings to look for on Tohatsu MFS 75A to 115A outboards

Each page shows how the defect is found, what decides the grade and example findings written up at A, B and C.

ENGINE AND FUEL

Engine overheating

Why marine diesels overheat, chronic against acute overheating, the order to check the cooling system in, the temperature test for a blocked exhaust elbow, what a surveyor checks and three example findings graded A, B and C.

How to find and write it up
ENGINE AND FUEL

Outboard water pump impeller

How an outboard's water pump fails, the signs of a worn impeller, how often it should be changed, what the job costs, what a surveyor checks and three example findings graded A, B and C.

How to find and write it up
UNDERWATER GEAR

Damaged propeller

How to inspect a propeller for bent blades, nicks, cracks and a spun hub, when to repair and when to replace, the repitch limits for bronze and stainless, repair costs for aluminium and stainless, and three example findings graded A, B and C.

How to find and write it up

Frequently asked

Why is my Tohatsu outboard beeping and losing power?

A continuous buzzer with the engine speed limited means the ESG (Electronic Safety Governor) has stepped in. On the MFS 75A to 115A, Tohatsu's manual lists over-revving, low oil pressure and high engine temperature. Check which lamp is lit or flashing to tell them apart.

What does the flashing warning lamp mean on a Tohatsu outboard?

With a continuous buzzer, a flashing lamp means the engine temperature is abnormally high and speed is held to 1,800 rpm. Without the buzzer, it means a sensor or electrical fault, or battery overcharge. A flash of 1 second every 10 seconds is the 100 hour oil change reminder.

How do I reset a Tohatsu low oil pressure warning?

Tohatsu's manual says the engine has to be stopped to reset the warning system after a low oil pressure alarm. Move to a safe place, stop the engine and check the oil level, adding oil if needed. Consult a dealer if the level is too low or too high.

What does a Tohatsu outboard beep once at idle mean?

On the MFS 75A to 115A with variable idling, one short beep means the lowest idle speed, 650 rpm, has been set, and two beeps the highest, 850 rpm.

Your full survey report, minutes after the walk-round

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More fault codes

All fault codes
ENGINES AND OUTBOARDS

Honda BF115 to BF250 outboards

Honda outboard alarm codes from Honda's owner's manuals: the ACG, malfunction, oil pressure and overheat indicators, each buzzer pattern and what to do.

Look up a code
ENGINES AND OUTBOARDS

Fischer Panda PMS 5.5e generator

Fischer Panda generator fault codes from the PMS 5.5e manual: warning and shutdown messages, failed starts, high temperatures and low oil pressure.

Look up a code
DIESEL HEATERS

Webasto Air Top 2000 STC

Webasto heater error codes for the Air Top 2000 STC: F00 to F15 on the display, what each number of flashes means, and the lock-out reset.

Look up a code
DIESEL HEATERS

Eberspächer Airtronic S2 and M2

Eberspächer heater fault codes for the Airtronic S2 (D2) and M2 (D4): what each flashing code means, the P000 codes, and how a locked heater is cleared.

Look up a code
DIESEL HEATERS

Webasto Air Top Evo 40 and 55

Webasto Air Top Evo 40 and Evo 55 fault codes from Webasto's workshop manual: F00 to F19, the flash code count, the diagnostic codes and the lock-out reset.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron MPPT solar chargers

Victron MPPT error codes from Victron's own list: battery and PV errors, Err 67 BMS connection lost, Err 116, and which codes reset by themselves.

Look up a code

Report templates

FREE TEMPLATE · WORD

Engine survey

A free Word template for a marine engine survey report: engine records, visual inspection, cold start, readings under load, oil analysis and conclusions, with example findings graded A, B and C.

Open template
FREE TEMPLATE · WORD

Sea trial report

A free Word template for a sea trial report: conditions and load, checks before departure, engine readings at each speed, systems tested under way, the engine room after the run, and example findings.

Open template