Axsail
FAULT CODES · DIESEL HEATERS

Webasto Air Top Evo 40 and 55 fault codes: F00 to F19, the flash codes and how to clear a heater lock-out

UPDATED 16 NOVEMBER 2026 · 1 FINDINGS · 2 SOURCES

Webasto Air Top Evo 40 and Evo 55 fault codes from Webasto's workshop manual: F00 to F19, the flash code count, the diagnostic codes and the lock-out reset.

AT A GLANCE
Webasto Air Top Evo 40 and 55
MAKER
Webasto
COVERS
Air Top Evo 40 and Air Top Evo 55 air heaters, diesel (D) and petrol (B) versions
WHERE THE CODE SHOWS
F01 to F15 on a combination timer, or as long flashes after five short ones on a rotary control or Multi Control
CHECK FIRST
The fuel supply, then the combustion air intake and exhaust, then the hot air ducting

Webasto Air Top Evo 40 and Evo 55 fault codes run from F00 to F19. A combination timer shows them as F codes up to F15 and as "- -" above that. A rotary control or Multi Control flashes them: five short flashes, then count the long ones. Failed starts, flame aborts and overheats are counted, and enough of them lock the heater out. The codes below are from Webasto's Air Top Evo 40 / 55 workshop manual.

Fault codes

Code Fault What Webasto says to check
F00 Control unit defective, heater lock-out or room temperature sensor defective Clear the lock-out (below), otherwise the control unit
F01 No start: no flame even after a restart Fuel supply, exhaust temperature sensor deposits, evaporator mount
F02 Flame abort: flame went out and didn't relight Same checks as F01
F03 Undervoltage or overvoltage Below 10.5 V or 20.5 V for 20 seconds, or above 16 V or 32 V for 6 seconds
F04 Premature flame detection The exhaust temperature sensor
F07 Fuel pump defective Wiring and fuel pump, open or short circuit
F08 Drive motor open circuit, short circuit, overload or blocked Blockage, then the fan magnets and the drive unit
F09 Glow plug defective The glow plug
F10 Overheating The hot air guide: kinked line, closed outlet, dirty blow-out sensor
F14 Blow-out temperature sensor defective The sensor
F16 Exhaust temperature exceeded Combustion air and exhaust clear, CO2 setting, soot in the heat exchanger
F17 Exhaust temperature sensor defective Replace the sensor
F18 Setpoint generator defective Wiring and the control element
F19 Sensor plausibility incorrect The exhaust and blow-out temperature sensors

The manual lists F05, F06, F11, F12, F13 and F15 as not available on the Air Top Evo.

Diagnostic codes

A workshop reading the heater with Webasto Thermo Test sees a two-character code under each F code. Examples from the manual: 02 no flame after restart, 03 flame out during operation, 84 undervoltage, 04 overvoltage, 88 open circuit in the fuel pump, 19 short circuit in the glow plug, 06 overheated at the blow-out sensor and 4F upper exhaust temperature limit exceeded.

Lock-out

The control unit counts failures, and the heater locks out when a counter reaches its limit: 9 failed starts, 5 overheats, 3 flame aborts after restarts, or 5 other faults. A clean start into control mode resets the counters. To clear a lock-out, switch on, pull the fuse, refit it after more than 2 seconds and switch on again. Webasto adds that if serious faults such as overheating keep happening, the heater locks out permanently and needs a Webasto-trained technician.

For surveyors

Webasto's checks for F01 and F02 lead to the fuel supply and the exhaust, and for F10 to the hot air ducting, which on a boat often runs behind lockers. Check the exhaust skin fitting and that the cabin has a working CO alarm, as the no carbon monoxide alarm finding sets out. With Axsail, say "Webasto Air Top Evo 40, three long flashes, F03, heater on the same battery as the windlass" as you film the controller.

Findings to look for on Webasto Air Top Evo 40 and 55

Each page shows how the defect is found, what decides the grade and example findings written up at A, B and C.

GAS AND SAFETY

No CO alarm

Where a boat needs carbon monoxide detectors under the revised ABYC A-24, which detectors qualify, where not to fit them, what a surveyor checks and three example findings graded A, B and C.

How to find and write it up

Frequently asked

How do I read the flash code on a Webasto Air Top Evo?

On a rotary selector or Air Top Evo Multi Control, the operating light gives five short flashes, then a series of long ones. Webasto's workshop manual says to count the long flashes: that number is the fault code, so three long flashes is F03.

How do I reset a Webasto Air Top Evo heater lock-out?

For F00 with a heater lock-out, the workshop manual says to switch the unit on, remove the fuse, refit it after more than 2 seconds and switch on again. The lock-out can also be cleared with Webasto Thermo Test PC diagnostics. Find the cause first, or it will lock out again.

What is F01 on a Webasto Air Top Evo 40?

No start: no flame formed even after a restart. Webasto's checks are the fuel supply (tank empty, lines blocked), deposits on the exhaust temperature sensor seen through the exhaust fitting, and the evaporator mount.

What does F10 mean on a Webasto Air Top Evo?

Overheating. The workshop manual lists the causes in the hot air guide: pressure loss too high, a kinked line, a closed air outlet or a dirty blow-out temperature sensor.

Your full survey report, minutes after the walk-round

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More fault codes

All fault codes
DIESEL HEATERS

Webasto Air Top 2000 STC

Webasto heater error codes for the Air Top 2000 STC: F00 to F15 on the display, what each number of flashes means, and the lock-out reset.

Look up a code
DIESEL HEATERS

Eberspächer Airtronic S2 and M2

Eberspächer heater fault codes for the Airtronic S2 (D2) and M2 (D4): what each flashing code means, the P000 codes, and how a locked heater is cleared.

Look up a code
ENGINES AND OUTBOARDS

Honda BF115 to BF250 outboards

Honda outboard alarm codes from Honda's owner's manuals: the ACG, malfunction, oil pressure and overheat indicators, each buzzer pattern and what to do.

Look up a code
ENGINES AND OUTBOARDS

Tohatsu MFS 75A to 115A outboards

Tohatsu outboard warning codes from Tohatsu's owner's manual for the MFS 75A, 90A and 115A: each buzzer and lamp pattern with its remedy, and the ESG speed limits.

Look up a code
ENGINES AND OUTBOARDS

Fischer Panda PMS 5.5e generator

Fischer Panda generator fault codes from the PMS 5.5e manual: warning and shutdown messages, failed starts, high temperatures and low oil pressure.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron MPPT solar chargers

Victron MPPT error codes from Victron's own list: battery and PV errors, Err 67 BMS connection lost, Err 116, and which codes reset by themselves.

Look up a code