Axsail
FAULT CODES · ENGINES AND OUTBOARDS

Fischer Panda generator fault codes: the warning and shutdown messages on the control panel and what to check

UPDATED 16 NOVEMBER 2026 · 2 FINDINGS · 1 SOURCES

Fischer Panda generator fault codes from the PMS 5.5e manual: warning and shutdown messages, failed starts, high temperatures and low oil pressure.

AT A GLANCE
Fischer Panda PMS 5.5e generator
MAKER
Fischer Panda
COVERS
The Fischer Panda PMS 5.5e marine generator and its control panel
WHERE THE CODE SHOWS
As a text message on the control panel: dark text on light for a warning, light text on dark for a shutdown
CHECK FIRST
The sea water valve and strainer, water flow from the exhaust, and the electrical load on the generator

Fischer Panda generator fault codes on the PMS 5.5e are text messages on the control panel. A warning, dark text on a light background, means a reading is approaching its limit, and it goes away when the reading recovers. A shutdown, light text on dark, means the limit has been reached, and the generator stops soon after. The messages below are from Fischer Panda's PMS 5.5e manual.

Common messages and fixes

Message Likely cause from the manual What to do
Start attempt failed No speed signal: low fuel, clogged fuel filter, failed fuel pump Add fuel, replace the filters or the pump
Max. No. of failed starts Start attempts used up Stop trying: water collects in the exhaust. Contact a dealer
Exh. m. temp. high No or restricted sea water flow Open the sea water valve, clean the strainer, check water in the exhaust, replace the impeller
Cyl. h. temp. high Overload, sea water flow, low oil, low coolant, air in the coolant Reduce the load, fix the water flow, top up and bleed the coolant
Coil temp. is high Overload, alternator air intake blocked Reduce the load, clear the air intake
Oil pressure is low Low engine oil, sensor not connected Fill to the full mark, check the sensor connection
Starter batt. voltage low Poor battery connection or low battery Check both connections, measure and charge
Unexpected engine stop Oil pressure and speed lost without a stop command Low fuel, fuel filter, fuel pump
Water leak sensor trigger Water detected in the generator capsule Look inside the capsule for the source

Other control panel messages

Message Meaning
Actuator fault Speed control actuator calibration failed
Batt. voltage too low Starter battery below what the control system allows
Check/bleed coolant system Cylinder head temperature above the maximum
CHECK FIRE SYSTEM Remote stop contacts open, if enabled for a fire system
Fuel pump is in S.C. Short circuit on the fuel pump output
Glow plugs in SC Short circuit on the glow plug output
Lost inverter connection Engine controller no longer talking to the inverter
Output power high Output above the programmed maximum
Restart delay Minimum time since the last shutdown hasn't passed
Tank level is low Generator fuel tank low

Acknowledging and restarting

Press Alarm Mute to silence the alarm. A shutdown message stays until Start/Stop is pressed. Fischer Panda's caution is that operation outside the limits damages the generator, so the cause has to be fixed before restarting. It also says repeated failed starts can fill the exhaust with water until it enters the engine through the exhaust manifold.

For surveyors

Run the generator under load for long enough to warm up and watch the panel. Look at the sea water strainer, the exhaust outlet's water flow and the capsule for water, and compare the installation with the generator exhaust finding. With Axsail, say "Fischer Panda 5.5, Exh. m. temp. high after 12 minutes at 3 kW, strainer basket fouled" and it goes into the engine survey report.

Findings to look for on Fischer Panda PMS 5.5e generator

Each page shows how the defect is found, what decides the grade and example findings written up at A, B and C.

ENGINE AND FUEL

Generator exhaust

Why a boat's generator exhaust is the leading cause of carbon monoxide deaths on houseboats, what a surveyor checks in the exhaust run and where it exits, and three example findings graded A, B and C.

How to find and write it up
UNDERWATER GEAR

Seized seacocks

Why a seacock that won't close is a safety finding, how surveyors check seacocks and through-hulls, the ABYC strength test a ball valve on a through-hull can fail, replacement costs and three example findings graded A, B and C.

How to find and write it up

Frequently asked

What does Start attempt failed mean on a Fischer Panda generator?

The control system tried to start the engine but saw no speed signal. Fischer Panda's manual lists low fuel, a clogged fuel filter or a failed fuel pump, or a bad AC speed signal connection if the engine actually runs. It warns that repeated failed starts let water build up in the exhaust and enter the engine.

Why does my Fischer Panda show Cyl. h. temp. high?

The cylinder head temperature is above the programmed maximum. The manual's causes are an overloaded generator, no or restricted sea water flow, low engine oil, low coolant or air in the coolant. Reduce the load, open the sea water valve, clean the strainer and check the impeller.

How do I clear a shutdown message on a Fischer Panda?

The shutdown message stays on screen until the Start/Stop button is pressed to acknowledge it. The Alarm Mute button silences the alarm. Fischer Panda says to resolve the cause before running the generator again.

What is Unknown msg. or al. pending on a Fischer Panda panel?

The panel doesn't recognise a message or error code. Fischer Panda asks you to write down all the numbers next to the Code lines on the view more data screen and contact them.

Your full survey report, minutes after the walk-round

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More fault codes

All fault codes
ENGINES AND OUTBOARDS

Honda BF115 to BF250 outboards

Honda outboard alarm codes from Honda's owner's manuals: the ACG, malfunction, oil pressure and overheat indicators, each buzzer pattern and what to do.

Look up a code
ENGINES AND OUTBOARDS

Tohatsu MFS 75A to 115A outboards

Tohatsu outboard warning codes from Tohatsu's owner's manual for the MFS 75A, 90A and 115A: each buzzer and lamp pattern with its remedy, and the ESG speed limits.

Look up a code
DIESEL HEATERS

Webasto Air Top 2000 STC

Webasto heater error codes for the Air Top 2000 STC: F00 to F15 on the display, what each number of flashes means, and the lock-out reset.

Look up a code
DIESEL HEATERS

Eberspächer Airtronic S2 and M2

Eberspächer heater fault codes for the Airtronic S2 (D2) and M2 (D4): what each flashing code means, the P000 codes, and how a locked heater is cleared.

Look up a code
DIESEL HEATERS

Webasto Air Top Evo 40 and 55

Webasto Air Top Evo 40 and Evo 55 fault codes from Webasto's workshop manual: F00 to F19, the flash code count, the diagnostic codes and the lock-out reset.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron MPPT solar chargers

Victron MPPT error codes from Victron's own list: battery and PV errors, Err 67 BMS connection lost, Err 116, and which codes reset by themselves.

Look up a code

Known code problems

GENERATORS

Marine generators

Common problems on marine generators and where to look: starting power, clogged fuel filters on gensets that sit unused, raw water flow and strainers, generators mounted low in wet bilges or squeezed between the engines, and carbon monoxide.

What to check

Report templates

FREE TEMPLATE · WORD

Engine survey

A free Word template for a marine engine survey report: engine records, visual inspection, cold start, readings under load, oil analysis and conclusions, with example findings graded A, B and C.

Open template