Axsail
FAULT CODES · DIESEL HEATERS

Webasto heater error codes: the F codes and blink codes on an Air Top 2000 STC, and how to reset a lock-out

UPDATED 16 NOVEMBER 2026 · 1 FINDINGS · 2 SOURCES

Webasto heater error codes for the Air Top 2000 STC: F00 to F15 on the display, what each number of flashes means, and the lock-out reset.

AT A GLANCE
Webasto Air Top 2000 STC
MAKER
Webasto
COVERS
The Air Top 2000 STC air heater, diesel and petrol versions
WHERE THE CODE SHOWS
F01 to F15 on a control element with a display. On one without a display, the indicator light flashes: the number of long pulses is the fault number
CHECK FIRST
The fuse and plug connectors, then the combustion air intake and the exhaust for blockages

Webasto heater error codes on the Air Top 2000 STC run from F00 to F15. A control with a display shows the code as text, and a control without one flashes it: the number of long flashes is the fault number. Most codes point to air, fuel or the glow plug, and F12 means the heater has locked itself out. The codes below are from Webasto's operating instructions and the troubleshooting section of its workshop manual.

Code Fault What to check
F00 Control unit defective Rapid flashing on a control without a display. The W-bus wiring and control element, then the control unit
F01 No start Air intake and exhaust, fuel system, fuel pump, glow plug
F02 Flame failure The flame went out and didn't relight. Same checks as F01
F03 Supply voltage too high or too low The system voltage. Charge the battery
F04 Flame detected before combustion Air intake, exhaust, fuel system, glow plug
F05 Flame sensor interruption A break or short in the flame sensor circuit
F06 Temperature sensor interruption The internal or external temperature sensor circuit
F07 Fuel pump interruption A break or short in the fuel pump circuit
F08 Combustion air fan short circuit or blocked The fan motor and both fan wheels for snagging
F09 Glow plug interruption The glow plug or ignition unit circuit
F10 Heater overheated Hot and cold air ducts clear, then air intake, exhaust and fuel
F11 Overheat sensor interruption The overheating sensor circuit
F12 Heater lock-out Reset the lock-out, then read the other stored faults
F14 Overheat sensor gradient too low at start Position of the overheating sensor, fuel supply
F15 Setpoint potentiometer interruption The setpoint sensor circuit

The operating instructions say codes above F15 show as "- -" on a display.

Hex codes from the diagnostic tool

A workshop reading the heater with Webasto Thermo Test sees two-digit hex codes, with more detail than the F codes. Examples from the workshop manual: 02 no start, 03 flame failure, 06 overheated, 07 heater lock-out, 0A glow plug short circuit, 12 W-bus communication failure, 15 combustion air fan blocked, 84 operating voltage too low and 88 fuel pump interruption.

Resetting a lock-out

The heater locks out when the fault counter passes 10, the false start counter passes 7 or the overheating counter passes 20, according to the workshop manual. To reset: switch the heater on, pull fuse F1 for at least 10 seconds, switch the heater off, refit the fuse and switch on. If it locks out again, the cause from the earlier codes is still there.

Webasto also asks owners to run the heater every 4 weeks, so its moving parts don't seize, and to have it checked by a professional at the start of each heating season.

For surveyors

A heater code is a reason to look at the exhaust run and the hull outlet as much as at the heater. Webasto's own warning is that a blocked exhaust or combustion air path can make the heater unsafe, so check there's a working CO alarm in the cabin, as the no carbon monoxide alarm finding sets out. With Axsail, say "Webasto heater, F10 on the controller, hot air duct crushed behind the saloon locker" as you photograph it.

Findings to look for on Webasto Air Top 2000 STC

Each page shows how the defect is found, what decides the grade and example findings written up at A, B and C.

GAS AND SAFETY

No CO alarm

Where a boat needs carbon monoxide detectors under the revised ABYC A-24, which detectors qualify, where not to fit them, what a surveyor checks and three example findings graded A, B and C.

How to find and write it up

Frequently asked

What do the Webasto flashing codes mean?

On a control without a display, Webasto's operating instructions say the light gives short and long pulses, and the number of long pulses is the fault code: five long flashes is F05, a break in the flame sensor circuit. Rapid flashing on its own is F00, a control unit fault.

How do I reset a Webasto heater lock-out?

Webasto's workshop manual gives the procedure for F12: switch the heater on, pull fuse F1 for at least 10 seconds, switch the heater off, refit fuse F1 and switch it on again. The heater locks out after more than 10 faults, 7 failed starts or 20 overheating events, so read the other stored codes first.

What is F01 on a Webasto heater?

No start: no flame formed even after a repeated start attempt. Webasto lists four checks: the air intake and exhaust, the fuel system, the fuel pump and the glow plug.

What does F10 mean on a Webasto?

The heater overheated and its overheating lock-out tripped. Check the hot and cold air ducts are clear, switch the heater off and let it cool, then check the air intake, exhaust and fuel system.

Your full survey report, minutes after the walk-round

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More fault codes

All fault codes
DIESEL HEATERS

Eberspächer Airtronic S2 and M2

Eberspächer heater fault codes for the Airtronic S2 (D2) and M2 (D4): what each flashing code means, the P000 codes, and how a locked heater is cleared.

Look up a code
DIESEL HEATERS

Webasto Air Top Evo 40 and 55

Webasto Air Top Evo 40 and Evo 55 fault codes from Webasto's workshop manual: F00 to F19, the flash code count, the diagnostic codes and the lock-out reset.

Look up a code
ENGINES AND OUTBOARDS

Honda BF115 to BF250 outboards

Honda outboard alarm codes from Honda's owner's manuals: the ACG, malfunction, oil pressure and overheat indicators, each buzzer pattern and what to do.

Look up a code
ENGINES AND OUTBOARDS

Tohatsu MFS 75A to 115A outboards

Tohatsu outboard warning codes from Tohatsu's owner's manual for the MFS 75A, 90A and 115A: each buzzer and lamp pattern with its remedy, and the ESG speed limits.

Look up a code
ENGINES AND OUTBOARDS

Fischer Panda PMS 5.5e generator

Fischer Panda generator fault codes from the PMS 5.5e manual: warning and shutdown messages, failed starts, high temperatures and low oil pressure.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron MPPT solar chargers

Victron MPPT error codes from Victron's own list: battery and PV errors, Err 67 BMS connection lost, Err 116, and which codes reset by themselves.

Look up a code