Axsail
FAULT CODES · CHARGERS, INVERTERS AND BATTERIES

Victron MPPT error codes: what Err 2, 21, 28, 33, 38, 67, 116 and the rest mean on a SmartSolar or BlueSolar charger

UPDATED 16 NOVEMBER 2026 · 2 FINDINGS · 1 SOURCES

Victron MPPT error codes from Victron's own list: battery and PV errors, Err 67 BMS connection lost, Err 116, and which codes reset by themselves.

AT A GLANCE
Victron MPPT solar chargers
MAKER
Victron Energy
COVERS
All Victron MPPT solar chargers (SmartSolar and BlueSolar), Skylla battery chargers, Inverter RS and Multi RS, and the Orion Smart DC-DC charger
WHERE THE CODE SHOWS
As a number in the VictronConnect app or on a GX device or MPPT Control panel. The charger itself shows errors with its LEDs, decoded in Victron's Toolkit app
CHECK FIRST
Whether the error is active or only in the history, then the battery voltage setting and every cable on the battery and PV side

A Victron MPPT error code is a number the solar charger reports when it stops or limits charging to protect itself or the battery. You read it in the VictronConnect app or on a GX device. Some errors clear on their own once the cause has gone, others need a restart or point to a faulty unit. The meanings below are from Victron's own error code list, which also covers Skylla chargers, the Inverter RS and Multi RS, and the Orion Smart DC-DC charger.

Battery side errors

Code Meaning What to check
Err 1 Battery temperature too high Clears once the battery cools. The reading comes from an external sensor, such as a Smart Battery Sense or BMV, or from the charger itself
Err 2 Battery voltage too high Another charger on the same battery, a fault in the controller, or a battery voltage setting lower than the battery fitted
Err 3, Err 4 Remote temperature sensor failure The T-sense connector, most likely wired to BAT+ or BAT- by mistake
Err 5 Remote temperature sensor connection lost The T-sense connection. Doesn't clear by itself
Err 6, Err 7 Remote battery voltage sense failure The V-sense connector, most likely wired in reverse polarity
Err 8 Remote voltage sense connection lost The V-sense connection to the battery terminals
Err 14 Battery low temperature Charging stopped so a LiFePO4 battery isn't charged in the cold, which damages the cells
Err 29 Over-charge protection Too many panels in series, absorption and float settings that don't match the battery, or another charger pushing the voltage up
Err 67 BMS connection lost The charger is set for BMS control but gets no messages: check the BMS link. The setting survives a power cycle

Charger and PV side errors

Code Meaning What to check
Err 17 Controller overheated despite reduced current Ambient temperature and anything blocking the heatsink
Err 18 Controller over-current A large load switched on the battery side, or an overloaded inverter. Restart after 3 minutes if it doesn't clear
Err 21 Current sensor issue Reconnect all wires. Victron says the controller is probably faulty if it stays
Err 26 Terminal overheated The power terminals: cable type, strands and tight bolts
Err 27 Charger short circuit Over-current on the battery side, for example a battery switched in through a contactor
Err 28 Power stage issue Reconnect all wires. If it stays, Victron says the unit needs replacing
Err 33 PV over-voltage The array's open-circuit voltage is too close to the charger's limit: rearrange the panels
Err 34 PV over-current Restart after 3 minutes. If it stays, the controller is probably faulty
Err 38, Err 39, Err 80 to 87 PV input shutdown The PV input is shorted to protect the battery. Usually a wrong battery voltage setting, or another charger set higher
Err 40 PV input failed to shut down The charger disconnects its own output and becomes faulty
Err 114 CPU temperature too high Ventilation around the cabinet
Err 116 Calibration data lost Serious only if active and the unit won't work
Err 117 Incompatible firmware A firmware update didn't finish: run it again
Err 119 Settings data lost Reset to factory defaults, power off for 3 minutes, reconfigure

The Inverter RS and Multi RS have their own codes in the same list: Err 50 and 52 for overload, Err 51 for inverter temperature, Err 53 and 54 for low output voltage, and Err 69 to 77 for networked units that don't match.

Errors that clear by themselves

Victron's list marks some errors as auto-reset: battery temperature (Err 1), battery voltage (Err 2), terminal overheating (Err 26) and PV over-voltage (Err 33) among them. Others stay until someone acts: Err 5, Err 21, Err 28 and Err 119 never clear on their own. For a solar charger, Err 67 appears only when there's sun, so a lasting BMS problem shows each morning and disappears at night.

For surveyors

An error in the charger's history isn't the same as a fault today, so note whether it's active. A charger showing Err 2 or Err 29 next to a second charger, or Err 67 on a lithium bank, says more about the system than the charger. Check it against the lithium batteries without a BMS finding and the ABYC E-11 rules for overcurrent protection. With Axsail, say "solar charger, Err 67 active, BMS cable unplugged at the GX" as you photograph the screen and it goes into the electrical section.

Findings to look for on Victron MPPT solar chargers

Each page shows how the defect is found, what decides the grade and example findings written up at A, B and C.

ELECTRICAL

Lithium batteries without a BMS

What ABYC E-13 asks of lithium battery systems on boats, why a battery management system is required, what a surveyor checks on a lithium install and three example findings graded A, B and C.

How to find and write it up
ELECTRICAL

Missing overcurrent protection

Why an unfused battery cable is a fire risk, the ABYC E-11 rule surveyors check against, which fuse types suit which battery banks, what the fix costs and three example findings graded A, B and C.

How to find and write it up

Frequently asked

What does error 67 mean on a Victron MPPT?

BMS connection lost. Victron says the charger is set to be controlled by a battery management system but isn't receiving its messages, so it drops its output to the battery's base voltage. Check the connection to the BMS. A charger moved from a BMS system to one without keeps the setting after a power cycle, so it has to be cleared.

How do I reset a Victron MPPT error?

Many errors clear by themselves once the cause is gone, such as a battery temperature or voltage that drops back. For others Victron's list says to disconnect the charger from all power sources, wait 3 minutes and power it up again. Err 119, settings data lost, needs a reset to factory defaults and a full reconfiguration.

Is error 116 on a Victron charger serious?

Only if it's the active error and the charger doesn't work: then Victron says the unit is faulty and should be replaced through the dealer. If it only appears in the history and the charger works normally, it can be ignored. Some units left the factory with it logged.

Where do I read the error code on a Victron solar charger?

In the VictronConnect app over Bluetooth or cable, or on a remote panel such as a GX device or the MPPT Control. On the charger itself the LEDs show that there's an error; Victron's Toolkit app decodes the LED pattern.

Your full survey report, minutes after the walk-round

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More fault codes

All fault codes
CHARGERS, INVERTERS AND BATTERIES

Victron MultiPlus and Quattro (VE.Bus)

Victron VE.Bus error codes for MultiPlus and Quattro inverter chargers: error 11 relay test, error 24 switch-over protection, and which codes keep the system off.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron BatteryProtect

Victron BatteryProtect and Smart BatteryProtect error codes: E1 to E4 on every model, E0 and E5 to E8 on the Smart versions, and the P2 and P3 warnings.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron Lynx Smart BMS

Victron Lynx Smart BMS error codes from Victron's manual: what 1 to 14 red LED flashes mean, the W-B warnings, A-B alarms, E-B errors and blown fuse alarms.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron Phoenix Inverter Smart

Victron Phoenix inverter error codes from Victron's manual: each LED pattern for overload, battery voltage, temperature and DC ripple, and the restarts.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron Orion XS DC-DC charger

Victron Orion XS error codes from Victron's manual: battery temperature, terminal overheated, BMS connection lost (error 67) and the 150 to 161 warnings.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron Cerbo GX and GX devices

Victron Cerbo GX error codes from Victron's manual: #42 storage corrupt, #46 data partition full, #48 DVCC firmware, #51 MK3 update and #60 MFD connection.

Look up a code

Standards to check against

ABYC E-11

AC and DC Electrical Systems on Boats

What ABYC E-11 covers on a boat's AC and DC systems, the rules surveyors check most often, from the 7 inch battery fuse rule to the reverse polarity indicator, and how to cite E-11 in a finding.

What surveyors check