Axsail
FAULT CODES · CHARGERS, INVERTERS AND BATTERIES

Victron Orion XS error codes: the DC-DC charger's errors and warnings, from error 1 to warning 161

UPDATED 16 NOVEMBER 2026 · 2 FINDINGS · 1 SOURCES

Victron Orion XS error codes from Victron's manual: battery temperature, terminal overheated, BMS connection lost (error 67) and the 150 to 161 warnings.

AT A GLANCE
Victron Orion XS DC-DC charger
MAKER
Victron Energy
COVERS
Orion XS DC-DC battery chargers, which charge a house battery from the alternator and starter battery
WHERE THE CODE SHOWS
In the VictronConnect app or on a connected GX device
CHECK FIRST
The power cables and terminal bolts, then the battery temperature sensor and any BMS link

Victron Orion XS error codes show in the VictronConnect app or on a GX device as a number and a short description. Errors stop the charger, and warnings reduce or pause charging while it carries on. Most clear themselves once the cause has gone. The ones that don't, such as 21, 28 and 119, need the wires disconnected or the settings restored. The list below is from Victron's Orion XS manual.

Error codes

Code Meaning Resets itself What to check
1 Battery temperature too high Yes Without a battery sensor, a hot charger reads as a hot battery
2 Battery voltage too high Yes Other charging equipment on the battery, or a charge controller fault
17 Controller overheated despite reduced current Yes Ambient temperature and how the unit is mounted for cooling
21 Current sensor issue No Disconnect and reconnect all wires. If it stays, a dealer
26 Terminal overheated Yes Wire type and strands, and tighten the terminal bolts
27 Charger short circuit Yes If it doesn't clear, disconnect all power for 3 minutes
28 Power stage issue No Disconnect and reconnect all wires. If it persists, the unit is probably faulty
33 Input voltage too high Yes Clears once the input voltage drops
67 BMS connection lost When the link returns The BMS cable and the BMS control setting
116 Calibration data lost Active and not working: faulty unit. Only in the history: ignore
117 Incompatible firmware Retry the firmware update
119 Settings data lost No Factory defaults, 3 minutes without power, reconfigure
120 Internal supply voltage error No Check the installation and restart. If it persists, faulty
122 History data corrupted No Clear the history in VictronConnect

Warnings

Code Meaning What happens
150 Battery temperature too high Output drops to 12 V until the battery cools
151 Battery temperature too low Charging stops to protect a lithium battery
160 Current derated, controller hot Current reduced until the charger cools
161 Short circuit detected Over-current on the battery side. Disconnect power for 3 minutes if it stays

Victron points out that warning 151 is a protection working as set, and the low temperature limit can be adjusted by the installer.

Error 67 and lithium systems

With a BMS in charge, error 67 is the one to understand. Fifteen seconds after the BMS messages stop, the Orion XS lowers its output to 12 V, which VictronConnect shows as a jump from bulk to float. The error itself appears only after 3 minutes, and only while the charger wants to charge. When the link comes back, it returns to bulk.

For surveyors

The Orion XS sits between the alternator side and a house bank, often lithium. Look at the cable runs at both ends and the terminal bolts, since errors 26 and 1 both trace back to heat. If it's under BMS control, check the BMS link and compare the installation with the lithium batteries without a BMS finding. With Axsail, say "Orion XS, error 26 in history, terminal bolt on the output loose" as you photograph it.

Findings to look for on Victron Orion XS DC-DC charger

Each page shows how the defect is found, what decides the grade and example findings written up at A, B and C.

ELECTRICAL

Lithium batteries without a BMS

What ABYC E-13 asks of lithium battery systems on boats, why a battery management system is required, what a surveyor checks on a lithium install and three example findings graded A, B and C.

How to find and write it up
ELECTRICAL

Missing overcurrent protection

Why an unfused battery cable is a fire risk, the ABYC E-11 rule surveyors check against, which fuse types suit which battery banks, what the fix costs and three example findings graded A, B and C.

How to find and write it up

Frequently asked

What is error 67 on a Victron Orion XS?

BMS connection lost. The charger is set to be controlled by a BMS but isn't receiving its messages. After 15 seconds it drops its output to the battery's base voltage, 12 V, and the error shows after 3 minutes so a briefly disconnected BMS can reconnect. Check the BMS cable and settings.

Why does my Orion XS show error 1 when the battery is cold?

Without an external battery temperature sensor, Victron says the Orion XS assumes the battery is at its own temperature during start-up and float. A charger that's hot is then read as a hot battery. An external battery temperature sense takes that assumption away.

What is error 26 on a Victron Orion XS?

Terminal overheated: the power terminals got too hot. Victron's manual says to check the wiring, including the wire type and strands, and tighten the bolts. It resets automatically.

How do I fix error 119 on a Victron charger?

Settings data lost. Restore factory defaults in VictronConnect, disconnect the charger from all power for 3 minutes, power it up and reconfigure it. Victron asks for the case to be reported to the dealer.

Your full survey report, minutes after the walk-round

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More fault codes

All fault codes
CHARGERS, INVERTERS AND BATTERIES

Victron MPPT solar chargers

Victron MPPT error codes from Victron's own list: battery and PV errors, Err 67 BMS connection lost, Err 116, and which codes reset by themselves.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron Lynx Smart BMS

Victron Lynx Smart BMS error codes from Victron's manual: what 1 to 14 red LED flashes mean, the W-B warnings, A-B alarms, E-B errors and blown fuse alarms.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron Cerbo GX and GX devices

Victron Cerbo GX error codes from Victron's manual: #42 storage corrupt, #46 data partition full, #48 DVCC firmware, #51 MK3 update and #60 MFD connection.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron MultiPlus and Quattro (VE.Bus)

Victron VE.Bus error codes for MultiPlus and Quattro inverter chargers: error 11 relay test, error 24 switch-over protection, and which codes keep the system off.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron BatteryProtect

Victron BatteryProtect and Smart BatteryProtect error codes: E1 to E4 on every model, E0 and E5 to E8 on the Smart versions, and the P2 and P3 warnings.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron Phoenix Inverter Smart

Victron Phoenix inverter error codes from Victron's manual: each LED pattern for overload, battery voltage, temperature and DC ripple, and the restarts.

Look up a code

Standards to check against

ABYC E-11

AC and DC Electrical Systems on Boats

What ABYC E-11 covers on a boat's AC and DC systems, the rules surveyors check most often, from the 7 inch battery fuse rule to the reverse polarity indicator, and how to cite E-11 in a finding.

What surveyors check