Axsail
FAULT CODES · CHARGERS, INVERTERS AND BATTERIES

Victron Cerbo GX error codes: GX errors #42 to #60, and where the other codes on the screen come from

UPDATED 16 NOVEMBER 2026 · 1 FINDINGS · 1 SOURCES

Victron Cerbo GX error codes from Victron's manual: #42 storage corrupt, #46 data partition full, #48 DVCC firmware, #51 MK3 update and #60 MFD connection.

AT A GLANCE
Victron Cerbo GX and GX devices
MAKER
Victron Energy
COVERS
The Cerbo GX and other Victron GX monitoring devices running Venus OS
WHERE THE CODE SHOWS
On the GX device's screen or Remote Console, and in the VRM portal
CHECK FIRST
Whether the code is the GX device's own or comes from a connected inverter-charger or solar charger

Victron Cerbo GX error codes come from two places. Codes shown as GX Error #42 to #60 are the GX device's own. Any other code on the screen comes from a connected device, usually a VE.Bus code from a MultiPlus or Quattro, or a charger code from a solar charger, and those have their own lists. The GX codes below are from Victron's Cerbo GX manual.

GX device error codes

Code Meaning Victron's solution
#42 Storage corrupt Return for repair or replacement. Can't be fixed by firmware or in the field
#46 Data partition full Free space below 10%, usually from third-party apps such as Node-RED or Signal K
#47 Data partition issue Internal storage likely damaged. Contact the dealer or installer
#48 DVCC with incompatible firmware Bring every device up to the firmware the DVCC chapter lists
#49 Grid meter not found ESS setups with an external grid meter: check wiring and configuration
#51 MK3 firmware needs update Start the update from the MultiPlus or Quattro device menu
#60 Could not connect to the GX device Reboot the GX device or the MFD

Victron's FAQ adds that with #42, settings can't be saved and revert to defaults after every reboot.

Codes from other devices

What the screen shows Where it comes from Look it up in
VE.Bus error with a number MultiPlus or Quattro inverter-charger Victron VE.Bus error codes
Error number on a solar charger SmartSolar or BlueSolar MPPT Victron MPPT error codes
Error number on a DC-DC charger Orion XS Victron Orion XS error codes
Alarm from the battery system Lynx Smart BMS Victron Lynx Smart BMS error codes

DVCC and error #48

DVCC is distributed voltage and current control, run from the GX device. Victron's manual notes that newer Venus OS versions switch DVCC on automatically for some lithium batteries, so an older system that updates can show #48 when one device's firmware is behind. Its advice is to have an installer bring all the devices up to date.

MK3 update and #51

The MK3 is the interface inside the GX device that talks to the inverter-charger. Victron says the one-off update can briefly restart the system, in around 5% of cases by its data, so the inverter-charger may cycle off and on. Do it when nothing on board depends on inverter power.

For surveyors

A GX device gives a quick history of the whole electrical system. Open the alarm and notification list on the screen or in VRM if the owner has access, and photograph any active code. A #42 means the settings on display may not be the ones the installer chose. With Axsail, say "Cerbo GX showing error 42, battery settings at defaults" as you photograph the screen.

Findings to look for on Victron Cerbo GX and GX devices

Each page shows how the defect is found, what decides the grade and example findings written up at A, B and C.

ELECTRICAL

Lithium batteries without a BMS

What ABYC E-13 asks of lithium battery systems on boats, why a battery management system is required, what a surveyor checks on a lithium install and three example findings graded A, B and C.

How to find and write it up

Frequently asked

What is error 42 on a Victron Cerbo GX?

Storage corrupt. Victron says the internal flash memory that holds settings, serial numbers and Wi-Fi credentials is corrupt, settings revert to defaults after a reboot, and the device must be returned for repair or replacement. It can't be fixed in the field.

What does GX error 48 mean?

DVCC is enabled but not every component in the system runs firmware compatible with it. Victron's manual points to the DVCC chapter for the firmware each device needs. Systems with some lithium battery brands can show it after a Venus OS update turned DVCC on.

Why does my Cerbo GX show a VE.Bus error?

The GX device displays error codes from connected devices as well as its own. A VE.Bus error number comes from the MultiPlus or Quattro inverter-charger, and Victron refers to its VE.Bus error code list for those.

What is GX error 60?

The Marine MFD app on a chartplotter couldn't connect to the GX device. Victron's fix is to reboot the GX device, the MFD or both.

Your full survey report, minutes after the walk-round

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More fault codes

All fault codes
CHARGERS, INVERTERS AND BATTERIES

Victron MultiPlus and Quattro (VE.Bus)

Victron VE.Bus error codes for MultiPlus and Quattro inverter chargers: error 11 relay test, error 24 switch-over protection, and which codes keep the system off.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron MPPT solar chargers

Victron MPPT error codes from Victron's own list: battery and PV errors, Err 67 BMS connection lost, Err 116, and which codes reset by themselves.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron Orion XS DC-DC charger

Victron Orion XS error codes from Victron's manual: battery temperature, terminal overheated, BMS connection lost (error 67) and the 150 to 161 warnings.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron BatteryProtect

Victron BatteryProtect and Smart BatteryProtect error codes: E1 to E4 on every model, E0 and E5 to E8 on the Smart versions, and the P2 and P3 warnings.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron Lynx Smart BMS

Victron Lynx Smart BMS error codes from Victron's manual: what 1 to 14 red LED flashes mean, the W-B warnings, A-B alarms, E-B errors and blown fuse alarms.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron Phoenix Inverter Smart

Victron Phoenix inverter error codes from Victron's manual: each LED pattern for overload, battery voltage, temperature and DC ripple, and the restarts.

Look up a code