Axsail
FAULT CODES · DIESEL HEATERS

Eberspächer heater fault codes: the Airtronic flashing codes 1 to 15, the P0 fault codes and how to clear a locked control box

UPDATED 16 NOVEMBER 2026 · 1 FINDINGS · 2 SOURCES

Eberspächer heater fault codes for the Airtronic S2 (D2) and M2 (D4): what each flashing code means, the P000 codes, and how a locked heater is cleared.

AT A GLANCE
Eberspächer Airtronic S2 and M2
MAKER
Eberspächer
COVERS
Airtronic S2 (D2L) and Airtronic M2 (D4L and D4R, plus the petrol B4L), 12 V and 24 V, including the Recreational version
WHERE THE CODE SHOWS
As a flashing code on the heater's LED, as "Err" on an EasyStart Remote+, or as a P000 code on EasyStart Pro, EasyStart Web and the EasyScan tool
CHECK FIRST
The exhaust and combustion air system, then the fuel supply and fuel filter

Eberspächer heater fault codes on the Airtronic S2 and M2 come in two forms: a flashing code from 1 to 15 on the heater, and a longer P000 code that the EasyStart Pro, EasyStart Web or EasyScan tool shows. Flame cutouts, failed starts and overheating account for most of them, and enough of those in a row lock the heater until it's cleared with a diagnostic control. The codes below are from Eberspächer's Airtronic S2 and M2 repair instructions.

Flashing codes

Flashes Error What to check
0 No fault, normal operation
1 Locking due to overheating The control box locked after too many overheating events: find the cause, then clear it with a diagnostic control
2 Overvoltage cut-off The supply voltage and charging system
3 Undervoltage cut-off The battery and the heater's supply cables
4 Glow plug defective Glow plug and its wiring
5 Burner motor defective The combustion air blower
6 Invalid configuration The control box setup
7 Safety time exceeded No flame within the start time: exhaust, combustion air, fuel
8 Overheating Air throughput, ducts and the overheating sensor
9 Metering pump defective The fuel metering pump and its wiring
10 External temperature sensor or setpoint transmitter defective The sensor and its cable
11 Combination sensor defective The combined flame and overheating sensor
12 Flame cutout Exhaust, combustion air, fuel supply, fuel filters
13 Too many exceedances of safety time 1 Repeated failed starts: fuel and air supply
14 Control box defective The control box
15 Other errors Needs EasyScan diagnosis

The P000 fault codes

A diagnostic control shows the same faults as P000 codes, with the older LIN number in brackets. A few from the repair instructions:

Code Fault Repair instructions say
P000114 (014) Possible risk of overheating The overheating sensor has reached at least 80 °C. Check the sensor and its cables
P000115 (012) Overheating, software threshold Over 125 °C at the overheating sensor. Check air throughput and the sensor
P000116 (017) Overheating, hardware threshold Over 130 °C. Same checks as P000115
P00011A (015) Operating lock-out, heater locked Too many overheating events. Fix the cause, then clear the lock with a diagnostic control
P000120 (064), P000121 (065) Flame sensor interruption or short circuit The sensor and its cable
P000125 to P00012A Flame cutout, at start or by output range Exhaust and combustion air, fuel quantity and supply, a new fuel filter

The repair instructions add that after a flame cutout the heater tries to restart up to 5 times, and a successful restart deletes the fault from the display. A code that keeps coming back is a real fault.

Reading the stored faults

The control box stores up to 20 faults, 10 active and 10 stored. The EasyScan tool, EasyStart Pro, EasyStart Web and EasyStart Remote+ can read them and clear the lock. A Remote+ shows "Err" for the current fault and lets you scroll stored faults F1 to F5. A plain switch on the S+ input can't be used for diagnosis.

For surveyors

Repeated flame cutouts and lock-outs usually trace back to the exhaust run, the combustion air intake or the fuel supply, so look at the hull exhaust outlet and the fuel standpipe as well as the heater. Check the cabin has a working CO alarm, as in the no carbon monoxide alarm finding. With Axsail, say "Eberspächer heater, flashes 12 times, soot at the exhaust skin fitting" and it's written up in the heating section.

Findings to look for on Eberspächer Airtronic S2 and M2

Each page shows how the defect is found, what decides the grade and example findings written up at A, B and C.

GAS AND SAFETY

No CO alarm

Where a boat needs carbon monoxide detectors under the revised ABYC A-24, which detectors qualify, where not to fit them, what a surveyor checks and three example findings graded A, B and C.

How to find and write it up

Frequently asked

What do the Eberspächer flashing codes mean?

On the Airtronic S2 and M2, the number of flashes is the error: 1 locking due to overheating, 2 overvoltage cut-off, 3 undervoltage cut-off, 4 glow plug defective, 5 burner motor defective, 7 safety time exceeded, 8 overheating, 9 metering pump defective, 12 flame cutout and 15 other errors that need EasyScan diagnosis.

How do I reset an Eberspächer heater that is locked?

Eberspächer's repair instructions say the lock is cleared with a diagnosis-capable control: the EasyScan tool, EasyStart Pro, EasyStart Web or EasyStart Remote+. The heater locks after too many overheating events or failed starts, so the cause has to be found first.

What is fault code 12 on an Eberspächer heater?

As a flashing code, 12 is flame cutout. The repair instructions list the checks: the exhaust and combustion air system, the fuel quantity and supply, a new fuel filter and cleaning the filter in the metering pump connection.

How many faults does an Eberspächer heater store?

Up to 20 in the control box, 10 active and 10 stored, per the repair instructions. A LIN control such as EasyStart Remote+ shows only 1 active and 5 stored faults.

Your full survey report, minutes after the walk-round

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More fault codes

All fault codes
DIESEL HEATERS

Webasto Air Top 2000 STC

Webasto heater error codes for the Air Top 2000 STC: F00 to F15 on the display, what each number of flashes means, and the lock-out reset.

Look up a code
DIESEL HEATERS

Webasto Air Top Evo 40 and 55

Webasto Air Top Evo 40 and Evo 55 fault codes from Webasto's workshop manual: F00 to F19, the flash code count, the diagnostic codes and the lock-out reset.

Look up a code
ENGINES AND OUTBOARDS

Honda BF115 to BF250 outboards

Honda outboard alarm codes from Honda's owner's manuals: the ACG, malfunction, oil pressure and overheat indicators, each buzzer pattern and what to do.

Look up a code
ENGINES AND OUTBOARDS

Tohatsu MFS 75A to 115A outboards

Tohatsu outboard warning codes from Tohatsu's owner's manual for the MFS 75A, 90A and 115A: each buzzer and lamp pattern with its remedy, and the ESG speed limits.

Look up a code
ENGINES AND OUTBOARDS

Fischer Panda PMS 5.5e generator

Fischer Panda generator fault codes from the PMS 5.5e manual: warning and shutdown messages, failed starts, high temperatures and low oil pressure.

Look up a code
CHARGERS, INVERTERS AND BATTERIES

Victron MPPT solar chargers

Victron MPPT error codes from Victron's own list: battery and PV errors, Err 67 BMS connection lost, Err 116, and which codes reset by themselves.

Look up a code