Check the trailer before the season, and the lights and tyres at every hook-up. The parts of a boat trailer diagram names each part. The list below follows Discover Boating's trailer maintenance checklist, with MasterCraft's tongue weight range. How old tyres can get is on how long boat trailer tyres last, and springs and bearings on when to replace trailer leaf springs.
The checklist, section by section
Tyres
Discover Boating says trailer tyres should be ST, special trailer, type and inflated to the sidewall maximum or the trailer's capacity sticker, which may be 60 psi or more. It cites the NTSB on replacing tyres more than six years old.
- ST trailer tyres, not LT light truck tyres
- Pressure set cold to the sidewall maximum or the capacity sticker
- Age from the DOT code, last four digits are week and year; replace past six years
- Even wear across the tread; uneven wear can mean a bent or misaligned axle
- Spare tyre on board, inflated, with a jack and lug wrench
Wheel bearings
Discover Boating recommends bearing protectors and repacking the bearings with fresh grease every three to five seasons.
- Bearing protectors fitted and topped up
- No grease thrown round the hub or wheel
- No play when the wheel is rocked top to bottom
- Date the bearings were last repacked
Brakes
Rinse salt-water brakes straight after launching. Discover Boating says to have pads or shoes looked at every few seasons and to check the fluid a couple of times a season.
- Brakes rinsed with fresh water after salt water
- Brake fluid reservoir level
- Brake lines free of rust and leaks
- Pads or shoes, date last inspected
Coupler and tongue weight
The surge brake actuator sits in the coupler and may need occasional lubrication. MasterCraft sets tongue weight between 5% and 10% of the total weight on the trailer.
- Coupler latches on the ball and locks
- Coupler and surge actuator lubricated
- Tongue weight measured, 5% to 10% of the loaded trailer
- Safety chains and breakaway cable attached
Lights and wiring
Check the lights every time you hook up. Discover Boating says a bad ground is the commonest cause of light failure, and dielectric grease protects the connections.
- Tail, brake and turn lights working with the tow vehicle
- Ground wire clean and tight
- Plug and sockets greased with dielectric grease
- Wiring free of chafe along the frame
Frame and wheels
Rinse the lug nuts so they don't rust tight, and look for rust where the frame sits in the water.
- Lug nuts rinsed and tight
- Frame and cross-members free of heavy rust
- Bunks or rollers supporting the hull evenly
- Boat tied down at bow and stern, drain plug position checked
Defects and actions
Write each defect, what's needed, who does it and whether it has to be fixed before the trailer is next towed.
- Defect
- Action needed
- By whom
- Done (date and initials)
Weigh it before you tow
Add the boat's dry weight, the engines, fuel, water, gear and the trailer itself, then check the total against the trailer's capacity sticker and the tow vehicle's rating. The boat trailer weight calculator does the sum and gives the tongue weight range.
Boat trailer wiring colour code
Most boat trailers use a 4-way flat plug. etrailer gives the standard colours:
| Wire | Function |
|---|---|
| White | Ground |
| Brown | Tail and running lights |
| Yellow | Left turn and brake |
| Green | Right turn and brake |
etrailer calls a bad ground the most common source of trailer light problems: fix the white wire to clean, bare frame metal with a ring terminal. It recommends at least 18 gauge for the lights and 16 gauge for the ground. Some wiring kits use red and black instead, so test each function with the tow vehicle plugged in.
For surveyors
A boat sold with its trailer often gets a look at the trailer during a pre-purchase survey, and the bill of sale prices the trailer on its own line. With Axsail you can say "trailer tyres ST, DOT code shows over six years, cracking on the sidewalls" as you walk round, and it lands as a finding with its photo.