Axsail
SURVEY TEST METHODS · RIG AND DECK

Rig tension gauge: how to measure shroud and forestay tension, and what the numbers should be

UPDATED 17 NOVEMBER 2026 · 3 SOURCES

How to use a rig tension gauge on a sailboat, from Loos and Selden's instructions: taking a reading, target tensions and the folding rule method.

AT A GLANCE
Rig tension gauge
MEASURES
Tension in standing rigging, read against the wire or rod's breaking strength
TOOLS
A Loos-type tension gauge sized for the wire or rod, or a 2 m folding rule and vernier callipers for Selden's method
WHEN TO USE
Rig surveys, after re-rigging or stepping a mast, and when a boat shows slack leeward shrouds under sail
READ WITH
The wire diameter and grade, and the gauge's conversion table

A rig tension gauge measures the load in a stay or shroud so it can be set as a percentage of the wire's breaking strength. Selden's tuning guide aims for cap shrouds at 15 to 20% of breaking load. Loos, which makes the most common gauge, puts the forestay on a masthead rig at about 15% and warns never to exceed 25%. The steps and figures below are from the Loos instructions and Selden's guide.

Taking a reading with a Loos gauge

  1. Check the wire diameter with the gauge's milled end, and use the model sized for it. The model 91 covers 3/32 to 5/32 inch wire, the model 90 3/16 to 9/32 inch; metric versions cover 2.5 to 7 mm.
  2. Hook the gauge on the wire.
  3. Pull the lanyard until the pointer sits on the black calibration mark at the inner end of the scale.
  4. Read the scale where the middle of the wire touches it, holding the gauge so the scale barely touches the wire.
  5. Convert the reading to tension with the table on the gauge.

Loos warns that pulling the pointer past the calibration mark can permanently bend the spring. The rod rigging gauges, RT-10 and RT-11, hook on and stay in place while you adjust, cover about 5 to 25% of the rod's breaking strength, and are accurate to plus or minus 5% at mid-range. Their slider slot needs regular silicone lubricant.

Target tensions

Stay Loos Selden
Forestay, masthead rig About 15% of breaking strength, as high as structurally allowed
Forestay, fractional rig At least 15%, eased if mast bend is excessive
Cap shrouds High enough that leeward shrouds stay tight close-hauled; 10 to 12% for many designs 15 to 20%
Shrouds on swept-spreader fractional rigs About 20%
Backstay Set to keep the mast straight; lower than the forestay 15%, briefly up to 30% with a tensioner
Absolute limit Never above 25%

Both makers say the right number depends on the boat, the rig type and the sails, and Loos suggests asking the sailmaker or designer first. Loos adds that on a masthead rig with roller furling, forestay tension can only be set through the backstay.

The folding rule method

Selden's alternative needs no gauge. On 1x19 wire, 1 mm of stretch over 2 metres equals 5% of breaking load, whatever the diameter:

  1. Tape a 2 m folding rule to the starboard cap shroud, its lower end about 5 mm above the terminal, and measure the gap exactly.
  2. Tension the shroud, then the port one by the same amount.
  3. Keep checking the starboard side as you go.
  4. When the gap has grown by 3 mm, the shroud is at 15% of breaking load.

Selden notes that Dyform and rod stretch differently, so allow for it, and suggests counting the rigging screw turns per millimetre for later adjustments.

Why tension matters

Loos's point is that slack rigging doesn't reduce the peak load on the hull. It lets the mast move and shock-load, and when leeward shrouds go slack the mast's lateral stiffness and the spreaders' fore and aft stiffness halve. Selden also limits mast pre-bend to 2% of the fore-triangle height, or 1% with in-mast furling.

For surveyors

On a rig survey, record each stay's wire size and gauge reading in pounds or as a percentage, and note any shroud that goes slack on the leeward side during the sea trial. With Axsail, say "starboard cap shroud, 7 mm wire, gauge reads 32" and it goes into the rig survey report as a table row with the photo.

Findings to look for

Each page shows how the defect is found, what decides the grade and example findings written up at A, B and C.

RIG

Standing rigging age

How old standing rigging can get, what insurers and riggers generally expect, why stainless wire gives little warning, what a surveyor checks and three example findings graded A, B and C.

How to find and write it up
RIG

Cracked swage terminals

Where standing rigging fails, how a surveyor spots cracked swage terminals and broken strands, the rigging age insurers look for, what re-rigging costs and three example findings graded A, B and C.

How to find and write it up
RIG

Chainplate crevice corrosion

Why stainless chainplates corrode where they pass through the deck, what a surveyor can see without pulling them, the signs that mean replacement, costs and three example findings graded A, B and C.

How to find and write it up

Frequently asked

How tight should sailboat shrouds be?

Selden's tuning guide aims for cap shrouds at 15 to 20% of the wire's breaking load, with the final check under sail. Loos says 10 to 12% is adequate for many shrouds and never to exceed 25% of breaking strength, with the test being that leeward shrouds don't go slack close-hauled in a brisk breeze.

How do you read a Loos tension gauge?

Hook the gauge on the wire, pull the lanyard until the pointer reaches the black calibration mark, then read the scale where the middle of the wire touches it. Convert the reading to tension with the table on the gauge for that wire diameter. Pulling past the mark can bend the spring permanently.

Can you tension a rig without a gauge?

Selden's folding rule method uses wire stretch: on 1x19 wire, 1 mm of elongation over 2 m equals 5% of breaking load whatever the diameter. Tape a 2 m rule to the shroud, tension until the gap at the terminal grows by 3 mm, and the shroud is at 15%.

Is a slack rig easier on the boat?

Loos says the opposite: a slack rig doesn't reduce the maximum load on the hull, and lets the mast and rigging move, chafe and shock-load. When leeward shrouds go slack, the mast's lateral stiffness is halved.

Your full survey report, minutes after the walk-round

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More test methods

All test methods
RIG AND DECK

Dye penetrant test

How to run a dye penetrant test on boat fittings with a red dye kit: cleaning, penetrant dwell, removing the excess, and what the test can and can't find.

Read the method
HULL AND STRUCTURE

Percussion test (hammer sounding)

How surveyors sound a fibreglass hull for delamination: which hammer or coin to use, tapping every 2 to 3 inches, and telling a dull thud from a bulkhead.

Read the method
HULL AND STRUCTURE

Ultrasonic thickness testing

Ultrasonic hull thickness testing on steel boats and narrowboats: gauge or A-scan, mill tolerance, wastage limits and the 4 mm insurance rule.

Read the method
HULL AND STRUCTURE

Inclining experiment

What an inclining experiment is for, how it is run under the MCA and Red Ensign codes, the 8 weight movements and when a lightweight check will do.

Read the method
HULL AND STRUCTURE

Underwater hull inspection

Underwater hull inspection by diver or ROV: site and visibility limits, the checklist of hull, running gear and openings, and what the diver's report must show.

Read the method
ENGINES AND MACHINERY

Diesel compression test

How to compression test a marine diesel: the kit, testing through injector or glow plug holes, typical readings and what low cylinders point to.

Read the method

Report templates

FREE TEMPLATE · WORD

Rig survey

A free Word template for a sailing yacht rig survey report: mast and spars, standing and running rigging, chainplates, furlers and rig age, with example findings graded A, B and C.

Open template

Related guides

YACHT SURVEYS · 3 MIN

Rig survey for sailing yachts: what's checked, what it costs and when insurers ask

What a rig survey covers on a sailing yacht, deck level, aloft or unstepped: mast, spreaders, terminals, chainplates and furlers, the age of the standing rigging, what it costs and which insurers ask for one.