Axsail
FAULT CODES · ELECTRONICS

Raymarine autopilot alarms: Drive stopped, Current limit, No pilot and the other Evolution alarm messages

UPDATED 16 NOVEMBER 2026 · 2 FINDINGS · 2 SOURCES

Raymarine autopilot alarms on Evolution pilots and p70 controllers, from Raymarine's manual: Drive stopped, Current limit, No pilot and AutoLearn fails.

AT A GLANCE
Raymarine Evolution autopilots
MAKER
Raymarine
COVERS
Evolution autopilots shown on p70, p70s, p70R and p70Rs pilot controllers
WHERE THE CODE SHOWS
As a text alarm on the pilot controller, also sent on the SeaTalkng network to the plotter
CHECK FIRST
The drive unit and its connections, the rudder reference and the SeaTalkng cabling

Raymarine autopilot alarms on Evolution pilots are text messages on the p70 or p70R pilot controller, also sent over SeaTalkng to the plotter. Most hardware alarms drop the pilot to standby and time out after 10 seconds, while a short circuit in the drive, clutch or solenoid powers the autopilot down. The meanings below are from Raymarine's p70 series instructions and its Evolution EV-2 installation manual.

Hardware and drive alarms

Alarm Meaning What to check
Drive stopped Rudder stall has persisted, or the drive unit has lost power Output from the autopilot, the drive unit and its connections
Current limit Drive overload current exceeded The drive unit and connections for a stall or short circuit
Drive short Short circuit in the drive unit. Autopilot powers down The drive unit and its cables
Clutch short Short circuit in the drive's clutch. Autopilot powers down The clutch circuit
Solenoid short Short circuit in the solenoid. Autopilot powers down The solenoid circuit
Rudder reference unit failure Rudder reference lost or beyond 50 degrees The rudder reference transducer and its cable
Rate gyro fault The gyro sensor has failed No owner check is given
EEPROM corruption Critical configuration data corrupted Pilot drops to standby, alarm times out after 10 seconds
Power and motor cables are swapped Motor and power pairs connected the wrong way Swap them at the course computer
SeaTalk fail SeaTalk data transmission problem Connections for a short or open circuit

On drive-by-wire boats with an EV-2 and a Volvo Penta EVC interface, pressing Auto less than a second after turning the wheel also gives Drive stopped, according to Raymarine.

Connection and data alarms

Alarm Meaning
No pilot The controller has lost the course computer
No control head The course computer has lost the controller
No drive detected Communication between the EV unit and the ACU has been lost
No compass Compass not detected
No navigation data No compass in Auto, no cross track error in Track or no wind angle in Wind vane mode
No Wind data No wind angle for 30 seconds in Wind vane mode. Pilot reverts to Auto
No speed data Check the speed transducer

For any of these, Raymarine's first step is to check the device works and every cable and connection is secure.

Off course, Large cross track error (more than 0.3 nm in Track mode), Wind shift (true wind angle changed by more than 15 degrees) and Auto release (someone took the wheel on a fly-by-wire boat) warn about the boat's course and the helm. Calibration required means the dockside and sea trial calibration hasn't been completed. AutoLearn fail 1 to 6 cover a calibration that wasn't run, was interrupted, hit a compass or drive error, reached the motor's current limit or sent the boat into a spin.

For surveyors

Most of these alarms only appear under way, so test the pilot on the sea trial. Engage Auto and make a few course changes. Drive stopped or Current limit under light load points to the drive unit, the hydraulic ram or the steering itself, so check against the hydraulic steering leak and stiff steering cable findings. With Axsail, say "autopilot engaged, Drive stopped after 20 seconds in Auto, ram weeping at the tiller arm" and it goes into the sea trial report.

Findings to look for on Raymarine Evolution autopilots

Each page shows how the defect is found, what decides the grade and example findings written up at A, B and C.

UNDERWATER GEAR

Hydraulic steering leak

How to check boat hydraulic steering on survey: leaks at the helm and ram seals, hoses and tubing, the bounce-back test for air, what a spongy wheel means, and three example findings graded A, B and C.

How to find and write it up
ENGINE AND FUEL

Stiff steering cable

Why mechanical outboard steering goes stiff and seizes, the twice-yearly maintenance the steering maker gives, how to tell a seized tilt tube from a failed cable, why cables can't be repaired, and three example findings graded A, B and C.

How to find and write it up

Frequently asked

What does Drive stopped mean on a Raymarine autopilot?

Raymarine says Drive stopped means a rudder stall has persisted, or power has been removed from the drive unit. It's triggered whenever the pilot is steering. Check the drive unit and its connections, and the autopilot's output to them. The pilot drops to standby and the alarm times out after 10 seconds.

What is the No pilot alarm on a Raymarine p70?

The pilot controller has lost communication with the course computer. The alarm comes from the controller itself. The matching No control head alarm comes from the course computer when it loses the controller. Check the SeaTalkng cables and power.

What does Current limit mean on a Raymarine autopilot?

The drive's overload current has been exceeded. The autopilot drops to standby and the alarm times out after 10 seconds. Raymarine says to check the drive unit and connections for a stall or a short circuit.

What does AutoLearn fail 6 mean?

AutoLearn failed because the boat went into a spin, meaning the motor didn't drive the rudder back to the other side. Raymarine says to restart the AutoLearn process first for any AutoLearn failure.

Your full survey report, minutes after the walk-round

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More fault codes

All fault codes
ENGINES AND OUTBOARDS

Honda BF115 to BF250 outboards

Honda outboard alarm codes from Honda's owner's manuals: the ACG, malfunction, oil pressure and overheat indicators, each buzzer pattern and what to do.

Look up a code
ENGINES AND OUTBOARDS

Tohatsu MFS 75A to 115A outboards

Tohatsu outboard warning codes from Tohatsu's owner's manual for the MFS 75A, 90A and 115A: each buzzer and lamp pattern with its remedy, and the ESG speed limits.

Look up a code
ENGINES AND OUTBOARDS

Fischer Panda PMS 5.5e generator

Fischer Panda generator fault codes from the PMS 5.5e manual: warning and shutdown messages, failed starts, high temperatures and low oil pressure.

Look up a code
DIESEL HEATERS

Webasto Air Top 2000 STC

Webasto heater error codes for the Air Top 2000 STC: F00 to F15 on the display, what each number of flashes means, and the lock-out reset.

Look up a code
DIESEL HEATERS

Eberspächer Airtronic S2 and M2

Eberspächer heater fault codes for the Airtronic S2 (D2) and M2 (D4): what each flashing code means, the P000 codes, and how a locked heater is cleared.

Look up a code
DIESEL HEATERS

Webasto Air Top Evo 40 and 55

Webasto Air Top Evo 40 and Evo 55 fault codes from Webasto's workshop manual: F00 to F19, the flash code count, the diagnostic codes and the lock-out reset.

Look up a code

Report templates

FREE TEMPLATE · WORD

Sea trial report

A free Word template for a sea trial report: conditions and load, checks before departure, engine readings at each speed, systems tested under way, the engine room after the run, and example findings.

Open template