Axsail
BOAT SYSTEMS · STEERING AND TRIM

Outboard power trim not working: motor, relay or hydraulics, and trim tabs that won't move

UPDATED 17 NOVEMBER 2026 · 5 SOURCES

Why outboard power trim stops working: test the relay click, the blue and green motor wires and the fluid, then trim tabs that won't move or work on one side.

AT A GLANCE
Power trim and trim tabs
SYMPTOM
Power trim and tilt does nothing, clicks, hums without moving, won't hold trim, or trim tabs won't move
CHECK FIRST
Battery charge and switch, fuses, then listen for the relay click at the helm switch
USUAL CAUSES
Failed relays or solenoids, corroded plugs and connections, a failed motor, low fluid from leaking ram seals, an open manual release valve, a failed pump
READ WITH
The engine's owner's manual for the release valve and the fluid it specifies

When outboard power trim stops working, the fault is either electrical, in the switch, relays and motor, or hydraulic, in the fluid, seals and pump. BoatUS's Frank Lanier, a marine surveyor, says the first step is to find out which, and a click, a hum or silence at the switch tells you most of it. The checks below come from his BoatUS article, Southern Boating, and Mercury's and Yamaha's owner's manuals, with a section on trim tabs from marine technician Andrew McDonald.

How it works

Most outboards use an electric-hydraulic unit: a reversing 12 or 24 volt motor drives a small pump, which pushes fluid from a reservoir to the rams that raise and lower the engine. Much of the same applies to sterndrives, BoatUS notes.

Nothing happens: the electrical side

  1. Battery charged, battery switch on. Check any trim fuses as well, and carry spares.
  2. Listen for the relay while pressing the helm switch up and down. Silence points to the helm switch and its relays, or the wiring between them.
  3. Try the switch on the engine cowl. If that works, the trim unit is fine and the fault is the helm switch or its wiring.
  4. A click means power reaches the relay. Test the motor next.
  5. Test the motor directly. With the battery switch off, disconnect the blue and green motor wires at the plug or relay. Apply 12 volts to blue to raise the engine and green to lower it; BoatUS's memory aid is "blue sky, green grass". Work with good ventilation and no fuel vapour.

If the motor runs on the jumper, the fault is upstream, in a relay or a corroded connection. If it doesn't, the motor has failed.

Motor runs, engine won't move or won't hold

Symptom Where BoatUS and Southern Boating point
Motor runs, engine won't raise or lower Fluid level, then the pump or valve body
Engine settles down from the raised position A leak, most often at the ram seals
Won't hold trim The hydraulic side: leak, pump or valve body
Erratic, though the level looks right Water in the reservoir

Hydraulic fluid doesn't evaporate, so a low level means a leak. Seals that have failed from age and sunlight can be replaced, but pitted rams ruin new seals, so rams and seals go together. With the level right and no leak, the pump is the likely cause, a job for a repair shop.

Check the manual tilt release valve too. Mercury's manual says it must be tightened before running, or the engine can tilt up in reverse. To check the fluid on Mercury's V6 and V8 models, tilt fully up on the support lever and look for fluid level with the bottom of the fill hole. Mercury specifies its own power trim and steering fluid, or automatic transmission fluid if that isn't available.

Raising it by hand

Mercury: turn the release valve out three turns counterclockwise, tilt by hand, then tighten. Yamaha's small four-strokes have a manual valve screw that is loosened fully counterclockwise to tilt and tightened clockwise to lock.

Trim tabs not working

Trim tabs use the same idea: a hydraulic or electric ram on each tab, fed from a pump and reservoir in the engine space. Andrew McDonald's checks by symptom:

  • Nothing happens. Check the connections from the battery to the helm switch, check the pump gets a signal, then power the pump directly.
  • The pump whines and the tabs don't move. Check the fluid level and for leaks, that the motor works, and that a ram isn't binding. Rams are the cheapest part and the one most often replaced.
  • Only one tab works. Look for a hydraulic leak or an electrical break, and top up the fluid.
  • The tabs move one way only. Check the fluid is full and the rams aren't binding.

He also notes the helm switch is labelled by the bow: "bow up" lowers the tabs.

For surveyors

Run the trim through its full range on the sea trial and with the boat on the hard, and look at the rams for weeping and pitting. Check the tabs move both sides. With Axsail, say "power trim full range, slow to lift, starboard ram weeping at the seal, release valve tight" and it goes on the sea trial report as a finding.

Findings to look for

Each page shows how the defect is found, what decides the grade and example findings written up at A, B and C.

UNDERWATER GEAR

Sterndrive bellows

Why sterndrive bellows sink boats at the dock, how to inspect all three, how often to replace them, what to check on the drive at the same time and three example findings graded A, B and C.

How to find and write it up
ENGINE AND FUEL

Outboard corrosion

Where outboards corrode, inside and out, how worn the anodes can get before they're replaced, why flushing matters, what a surveyor checks and three example findings graded A, B and C.

How to find and write it up

Frequently asked

Why is my outboard power trim not working?

BoatUS's Frank Lanier says the first job is to decide whether it's electrical or hydraulic. Check the battery and fuses, then listen for the relay at the helm switch. Failed relays and corroded plugs and connections are among the most common causes. If the motor runs and the engine doesn't move, look at the fluid and the pump.

My power trim clicks but doesn't move. What does that mean?

BoatUS says a slight click when you press the helm switch means power is reaching the solenoid or relay. Test the trim motor next by applying 12 volts directly to its blue wire to raise or its green wire to lower. If it runs, the fault is in the relay or connections; if it doesn't, the motor has failed.

How do I raise an outboard when the power trim won't work?

Open the manual tilt release valve. Mercury's manual says to turn it out three turns counterclockwise, tilt the engine by hand, then tighten it again, because a loose valve lets the engine tilt up in reverse. Yamaha's small models have a manual valve screw that works the same way.

Why are my trim tabs not working?

Marine technician Andrew McDonald lists low fluid from leaks, seized parts and damaged switches or connections. If nothing happens, check the connections from the battery to the switch and that the pump receives a signal. A whine without movement means checking the fluid, leaks and the motor, and whether a ram is binding.

Your survey report, minutes after the sea trial

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More boat systems

All boat systems
ENGINES AND FUEL

Outboard won't start

Why an outboard won't start and what to check in order: battery, neutral, kill switch lanyard, fuse, then fuel and spark when it turns over but won't fire.

Read the checks
STEERING AND TRIM

Bleeding hydraulic steering

How to bleed outboard hydraulic steering the SeaStar way: fill the helm, purge each side of the cylinder, check wheel turns lock to lock, then set the oil level.

Read the checks
STEERING AND TRIM

Steering cable replacement

How to replace a mechanical outboard steering cable: when it must be replaced, finding the part number, routing it with no tight bends, and fitting it.

Read the checks
ENGINES AND FUEL

Mercury outboard won't start

Why a Mercury outboard won't start or crank, from Mercury's troubleshooting chart: lanyard at RUN, neutral, the fuse, and priming after running dry.

Read the checks
ENGINES AND FUEL

Yamaha outboard won't start

Why a Yamaha outboard won't start, from Yamaha's own chart: neutral, the lanyard lock plate, choke, air vent screw, fuel, plugs and the 5-second crank rule.

Read the checks
ENGINES AND FUEL

Boat won't start

Why a boat won't start and what to check: battery switch, voltage and connections, neutral and kill switch, the starter if it clicks, fuel if it cranks.

Read the checks

Known engine problems

OUTBOARDS

Common outboard problems

Common outboard motor problems across Mercury, Yamaha, Honda and Suzuki, from their recalls and campaigns: shifting, idle, cooling, fuel and corrosion.

What to check

Report templates

FREE TEMPLATE · WORD

Sea trial report

A free Word template for a sea trial report: conditions and load, checks before departure, engine readings at each speed, systems tested under way, the engine room after the run, and example findings.

Open template
FREE TEMPLATE · WORD

Engine survey

A free Word template for a marine engine survey report: engine records, visual inspection, cold start, readings under load, oil analysis and conclusions, with example findings graded A, B and C.

Open template