Axsail
BOAT SYSTEMS · ENGINES AND FUEL

Mercury outboard won't start: lanyard, fuse, shift actuator and priming after running out of fuel

UPDATED 17 NOVEMBER 2026 · 2 SOURCES

Why a Mercury outboard won't start or crank, from Mercury's troubleshooting chart: lanyard at RUN, neutral, the fuse, and priming after running dry.

AT A GLANCE
Mercury outboard won't start
SYMPTOM
The starter won't crank, or the engine cranks and won't run, often after running the tank dry
CHECK FIRST
Lanyard stop switch at RUN, the control in neutral, and the clean power fuse
USUAL CAUSES
Lanyard, shift position, a blown fuse, a weak battery, a shift actuator that needs a key reset, air in the fuel supply module, a closed tank vent or a stuck anti-siphon valve
READ WITH
The operation and maintenance manual for the engine's serial number, and any fault shown on VesselView

A Mercury outboard that won't start is usually stopped by an interlock. Mercury's own troubleshooting chart puts the lanyard stop switch not at RUN and the control out of neutral at the top. If the engine ran out of fuel, its fuel supply module has to be primed before it will run. The checks below are from Mercury's operation and maintenance manual for its V6 and V8 DTS outboards; other Mercury models have their own manuals, so check the one for your serial number.

Starter won't crank the engine

Mercury's list, in its order:

  1. Lanyard stop switch not at RUN. Mercury also says to check before each use that pulling the lanyard stops the engine, and to have the switch repaired if it doesn't.
  2. Clean power circuit fuse open. The maintenance section shows where it sits.
  3. Control not in neutral.
  4. Shift actuator failure. Turn the key off to reset, then start again.
  5. Weak battery, or loose or corroded connections.
  6. Ignition key switch failure.
  7. Faulty wiring or connections.
  8. Starter solenoid or starter relay failure.

The key start is electronic: turn to START and release, and the system cranks by itself and stops if the engine doesn't fire. Turn to START again to retry.

Engine cranks but won't start

Cause in Mercury's chart What to look at
Incorrect starting procedure Vent open, lanyard at RUN, neutral, then key start
Old or contaminated fuel Fuel age and water in the separator
Fuel not reaching the engine Empty tank, line kinked or disconnected
Fuel tank vent closed or restricted Open the vent screw on manually vented tanks
Fuel filter or tank filter blocked Engine filter, and the pickup filter in the tank
Stuck anti-siphon valve Fitted on built-in tanks
Fuel system not primed See priming below
Fuel pump or ignition component failure A dealer job

Priming after running out of fuel

Mercury's fuel supply module isn't vented, so air trapped after running dry has to be pushed out. Mercury's procedure without a purge tool:

  1. Make sure the engine is level and vertical and the fuel line is connected.
  2. Turn the key on. The pumps run for about five seconds.
  3. Turn the key to START and release. The engine computer may crank for up to eight seconds.
  4. Repeat until the engine keeps running. Let the starter cool 20 to 30 seconds between full cranks, and stop after 10 full cranking events.
  5. Expect it to run rough at idle for up to two minutes while air clears.

Mercury warns that many key-on cycles without cranking won't finish the job and can damage the pumps. Where the supply is restrictive, such as a long line, an anti-siphon valve or a separating filter on the boat, Mercury prefers a purge tool on the fuel rail Schrader valve. If a primer bulb is fitted, squeezing it shortens priming either way.

After it starts

Mercury says to check for a steady stream from the water pump indicator hole. No water means stop the engine and check the intake.

For surveyors

Record the start: how many attempts it took, any priming, and the strength of the tell-tale stream. Check the lanyard stops the engine, as Mercury asks before each use, and note any fault on VesselView. With Axsail, say "starboard Mercury, started second key press, tell-tale strong, lanyard stop checked" and it goes into the engine survey report.

Findings to look for

Each page shows how the defect is found, what decides the grade and example findings written up at A, B and C.

ENGINE AND FUEL

Missing anti-siphon valve

When a gasoline boat's fuel line needs an anti-siphon valve under 33 CFR 183.568, the alternatives the rule allows, what a surveyor checks and three example findings graded A, B and C.

How to find and write it up
ENGINE AND FUEL

Fuel tank vent faults

What the US rules require of a gasoline boat's fuel tank vent, the flame arrester that must be cleanable, the 2 gallon a minute overflow rule, the vent line size the Coast Guard's handbook gives, signs of a blocked vent, and three example findings graded A, B and C.

How to find and write it up

Frequently asked

Why won't my Mercury outboard start?

Mercury's troubleshooting chart puts the lanyard stop switch first: the engine won't crank unless it's at RUN. Then the control must be in neutral, the clean power fuse intact, and the battery charged with tight, clean connections. If it cranks but won't run, the chart lists old fuel, an empty tank, a closed vent, a kinked line and blocked filters.

How do I prime a Mercury outboard after running out of fuel?

For its V6 and V8 DTS models Mercury says: engine level, key on so the pumps run about five seconds, then key to START and release; the starter may crank for up to eight seconds. Repeat until it runs, letting the starter cool 20 to 30 seconds between events, and stop after 10 full events.

My Mercury cranks but the shift won't engage. What does the manual say?

Mercury lists a shift actuator failure, with the remedy of turning the ignition key off to reset and then starting the engine again. Throttle only mode being engaged also stops it going into gear.

Why does my Mercury run rough right after it starts?

After priming a dry fuel system, Mercury says the engine may run rough at idle for up to two minutes while the remaining air is purged.

Your survey report, minutes after the sea trial

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More boat systems

All boat systems
ENGINES AND FUEL

Outboard won't start

Why an outboard won't start and what to check in order: battery, neutral, kill switch lanyard, fuse, then fuel and spark when it turns over but won't fire.

Read the checks
ENGINES AND FUEL

Yamaha outboard won't start

Why a Yamaha outboard won't start, from Yamaha's own chart: neutral, the lanyard lock plate, choke, air vent screw, fuel, plugs and the 5-second crank rule.

Read the checks
ENGINES AND FUEL

Boat won't start

Why a boat won't start and what to check: battery switch, voltage and connections, neutral and kill switch, the starter if it clicks, fuel if it cranks.

Read the checks
ENGINES AND FUEL

Fuel gauge and sending unit

Why a boat fuel gauge stops working and how to test it: the gauge, the sender wire, the ground, and the 33 to 240 ohm sending unit, with each sender type.

Read the checks
ENGINES AND FUEL

Outboard overheating

Why an outboard overheats, including when it's still pumping water: blocked intakes, a worn impeller, a stuck thermostat, salt in the passages and mounting height.

Read the checks
ENGINES AND FUEL

Outboard not peeing

Why an outboard stops peeing from its tell-tale, what Yamaha and Mercury say to do, and what it means when it's not peeing but not overheating.

Read the checks

Known engine problems

OUTBOARDS

Mercury Verado

Known problems and recalls on Mercury Verado outboards and where to look: the corroding shift bell crank stud on L6 Verados, the V12 steering position sensor recall, other USCG campaigns, and how to check a used Verado's recall status by serial number.

What to check
OUTBOARDS

Mercury 150 FourStroke

Mercury 150 FourStroke problems and recalls, Pro XS and SeaPro included: the idle air control valve recall, shift arm studs that corrode in salt water.

What to check
OUTBOARDS

Common outboard problems

Common outboard motor problems across Mercury, Yamaha, Honda and Suzuki, from their recalls and campaigns: shifting, idle, cooling, fuel and corrosion.

What to check

Report templates

FREE TEMPLATE · WORD

Engine survey

A free Word template for a marine engine survey report: engine records, visual inspection, cold start, readings under load, oil analysis and conclusions, with example findings graded A, B and C.

Open template