Axsail
BOAT SYSTEMS · ENGINES AND FUEL

Outboard not peeing: what the tell-tale shows and what to check when it stops

UPDATED 18 NOVEMBER 2026 · 4 SOURCES

Why an outboard stops peeing from its tell-tale, what Yamaha and Mercury say to do, and what it means when it's not peeing but not overheating.

AT A GLANCE
Outboard not peeing
SYMPTOM
No stream, or a weak one, from the tell-tale on the engine's cowling while it runs
CHECK FIRST
Stop the engine, then look at the cooling water intakes on the lower unit and the tell-tale outlet itself
USUAL CAUSES
A blocked intake or tell-tale outlet, a worn impeller, a flush connector left loose, or the intakes out of the water
READ WITH
The owner's manual, which names the outlet the pilot hole or water pump indicator hole

An outboard that stops peeing has lost its sign that cooling water is flowing. Yamaha calls the outlet the cooling water pilot hole and Mercury the water pump indicator hole, and both say a steady stream should come from it whenever the engine runs. When it stops, both makers say to stop the engine and check the intakes. The checks below come from their owner's manuals, with BoatUS on the impeller.

What the stream shows

Yamaha's manual says a continuous flow from the pilot hole shows the water pump is pushing water through the cooling passages. Canadian Boating describes where it comes from: the impeller in the leg draws water up to the powerhead, it runs through the engine, and some leaves through the tell-tale. Mercury asks for the check right after every start.

What to do when it stops

  1. Stop the engine. Yamaha warns that running without flow can cause overheating and serious damage.
  2. Check the intakes on the lower unit for weed, plastic or mud. Mercury's V6 and V8 have auxiliary intake holes as well as the main ones.
  3. Check the intakes are in the water. Both makers warn about tilting or trimming so far up that the intakes leave the water.
  4. Check the tell-tale outlet. Yamaha says to check whether the pilot hole itself is blocked.
  5. Check the flush connector. On the Yamaha, a garden hose connector left loose on its fitting lets the water leak out, and the engine can overheat.
  6. If nothing is blocked, Mercury says the cause may be a failed water pump or a blockage inside the cooling system, and the outboard should go to a dealer.

Not peeing but not overheating

A dry tell-tale with a normal gauge can be a blocked outlet or a pump that's starting to fail. Yamaha's manual treats any break in the flow as a reason to stop and check. Until the outlet is cleared and the stream returns, there's no way to tell a blocked outlet from a failing pump.

On muffs or a flushing attachment

Yamaha says never to run the engine without cooling water: the pump or the engine will be damaged. Both makers describe flushing with fresh water through the connector on the bottom cowling for about 15 minutes, with the engine off. Mercury asks for it after every use in salt or muddy water.

After an impeller replacement

BoatUS's walk-through of an outboard pump service gives the details that matter. Line up the keyway in the new impeller's hub with the key on the driveshaft. Use no oil or silicone, which can attack the rubber. Check the inside of the pump housing for score marks or gouges, which BoatUS says let water leak past the vanes. Every gasket and seal in the kit goes back on.

For surveyors

Report the stream at idle and at cruising revs, with the impeller change date if the records show one. A weak stream is a finding on its own, even with no alarm. With Axsail, say "tell-tale weak at idle, no change at 3,000, impeller date unknown" and the finding goes into the engine survey report with a recommendation to service the pump, as in the impeller finding. For the overheat itself, see outboard overheating.

Findings to look for

Each page shows how the defect is found, what decides the grade and example findings written up at A, B and C.

ENGINE AND FUEL

Outboard water pump impeller

How an outboard's water pump fails, the signs of a worn impeller, how often it should be changed, what the job costs, what a surveyor checks and three example findings graded A, B and C.

How to find and write it up

Frequently asked

Why is my outboard not peeing?

Yamaha and Mercury both say to stop the engine and check whether the cooling water intakes on the lower unit are blocked. Yamaha adds the pilot hole itself. Mercury says that if nothing is blocked, the cause may be a water pump failure or a blockage in the cooling system, and the engine should go to a dealer.

My outboard is not peeing but not overheating. Is that a problem?

Yamaha says that if water isn't flowing from the pilot hole at all times while the engine runs, overheating and serious damage could occur. Treat a dry tell-tale as a fault, even with the gauge still normal, and stop to check the intake and the outlet.

What is the tell-tale on an outboard?

A small outlet on the cowling that shows cooling water is flowing. Yamaha calls it the cooling water pilot hole and Mercury the water pump indicator hole. Canadian Boating explains that seawater runs through the engine and is spat out through it.

Why is my outboard not peeing after an impeller replacement?

BoatUS's impeller job lists the points to get right: line up the keyway in the new impeller's hub with the key on the shaft, and use no oil or silicone, which can attack the rubber. BoatUS also says a scored pump housing lets water leak past the vanes, so the pump works less well.

Your survey report, minutes after the sea trial

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More boat systems

All boat systems
ENGINES AND FUEL

Outboard overheating

Why an outboard overheats, including when it's still pumping water: blocked intakes, a worn impeller, a stuck thermostat, salt in the passages and mounting height.

Read the checks
ENGINES AND FUEL

Mercury outboard won't start

Why a Mercury outboard won't start or crank, from Mercury's troubleshooting chart: lanyard at RUN, neutral, the fuse, and priming after running dry.

Read the checks
ENGINES AND FUEL

Outboard won't start

Why an outboard won't start and what to check in order: battery, neutral, kill switch lanyard, fuse, then fuel and spark when it turns over but won't fire.

Read the checks
ENGINES AND FUEL

Yamaha outboard won't start

Why a Yamaha outboard won't start, from Yamaha's own chart: neutral, the lanyard lock plate, choke, air vent screw, fuel, plugs and the 5-second crank rule.

Read the checks
ENGINES AND FUEL

Boat won't start

Why a boat won't start and what to check: battery switch, voltage and connections, neutral and kill switch, the starter if it clicks, fuel if it cranks.

Read the checks
ENGINES AND FUEL

Fuel gauge and sending unit

Why a boat fuel gauge stops working and how to test it: the gauge, the sender wire, the ground, and the 33 to 240 ohm sending unit, with each sender type.

Read the checks

Known engine problems

OUTBOARDS

Common outboard problems

Common outboard motor problems across Mercury, Yamaha, Honda and Suzuki, from their recalls and campaigns: shifting, idle, cooling, fuel and corrosion.

What to check
OUTBOARDS

Yamaha four-stroke outboards

Known problems and recalls on Yamaha four-stroke outboards and where to look: the throttle linkage campaign on F200 and F225, the ignition coil recall on V MAX SHO models, the exhaust corrosion claims against first generation F-Series motors, and USCG campaigns.

What to check

Report templates

FREE TEMPLATE · WORD

Engine survey

A free Word template for a marine engine survey report: engine records, visual inspection, cold start, readings under load, oil analysis and conclusions, with example findings graded A, B and C.

Open template