Axsail
BOAT SYSTEMS · ELECTRICAL AND PROTECTION

Boat lightning protection: how a protection system works on a sailboat and what it can't do

UPDATED 17 NOVEMBER 2026 · 3 SOURCES

How lightning protection on a sailboat works: the air terminal, down conductors, a ground plate of a square foot or more, bonding, electronics, and side flashes.

AT A GLANCE
Lightning protection
SYMPTOM
A boat with no clear path from the masthead to the water, or one that has been struck
CHECK FIRST
Whether the mast connects to the keel or a ground plate, and how the rigging and large metal fittings are bonded
USUAL CAUSES
No grounding path, a ground plate too small for fresh water, unbonded fittings that allow side flashes, unprotected electronics
READ WITH
ABYC's technical report TE-4 and the NFPA lightning protection standard, which take different approaches

Lightning protection on a boat can't stop a strike. It gives the current a planned path from the masthead to the water, so it doesn't blow its own way through the hull, the crew or the wiring. Florida Sea Grant's bulletin by lightning researcher Ewen Thomson covers grounding and bonding, then the separate problem of saving the electronics. The guidance below comes from that bulletin and from Good Old Boat, which also quotes BoatUS's claims data.

How likely a strike is

BoatUS's figures, quoted in Good Old Boat, put the odds at 1.2 boats in 1,000 struck each year in the US, rising to 4 sailboats in 1,000 in Florida, where most claims occur. Thomson notes that boaters who are struck often say there were no storms in the area just before, because ground flashes can come from anywhere in a storm and slant out from its side.

The grounding system

Thomson's components:

  1. Air terminal at the masthead, where the strike should attach. With a VHF antenna or instruments up there, he says a separate terminal is highly desirable, high enough that the angle to anything else at the masthead is under 45 degrees, a cone of protection. Good Old Boat suggests at least 10 inches above the mast, pointed.
  2. Down conductors. An aluminium mast is the preferred conductor, much better than stainless stays.
  3. Mast base connection. A deck-stepped mast needs a heavy copper conductor from its base down to the ground strips; a keel-stepped mast is connected to the keel bolts.
  4. Grounding conductors in the water. In salt water a single plate of a square foot or more is usually enough, and a lead keel connected through the keel bolts is adequate. Paint or encapsulation on the keel doesn't seriously compromise it, though it may need minor repair after a strike.

Fresh water is far harder. Thomson says the voltages during a strike are about a thousand times higher than in salt water, and in his sample 40% of protected boats struck in fresh water had side flashes through the hull. It needs a ground strip along the stem connected to the forestay, mast base and backstay, plus extra strips outside the hull near metal fittings such as tanks.

Bonding and side flashes

Bonding joins large metal fittings with mainly horizontal conductors so big voltages can't build between them. Thomson lists toerails, chainplates, steering wheels, engine controls, pulpits and antenna bases. Without it, a side flash can jump from the rig to anything that leads towards the water. Good Old Boat gives examples it knows of: from the forestay to the chain in the locker and out through the hull above the waterline, and from a chainplate to a fuel tank and a through-hull.

ABYC and NFPA disagree

Good Old Boat explains that ABYC downgraded its lightning standard to a technical report, TE-4, which says complete protection isn't implied. NFPA's rewritten standard takes a building-style approach: mast, stays and shrouds joined in a loop at deck level, with several parallel conductors to electrodes totalling at least a square foot below the waterline. Good Old Boat notes there's little data yet on whether that works better, and each boat needs its own design. The ABYC page covers how surveyors cite its documents in a finding.

Electronics

Protection as fitted didn't save the electronics in Thomson's sample: 96% of the 71 struck boats lost at least some. His measures are transient suppressors at each piece of equipment and lightning arrestors on antennas, twisted-pair DC wiring, a heavy copper wire run parallel to each through-hull transducer cable, and disconnecting gear before a storm.

In a storm

Thomson's advice: keep away from the waterline and large metal fittings, and on an unprotected boat from beneath the mast and boom. Go below on a boat with a cabin. Don't get in the water.

For surveyors

Note whether there's a path from mast to keel or ground plate, its condition, and whether the rigging and large fittings are bonded. After a strike, follow the lightning strike damage checks. With Axsail, say "keel-stepped mast, no visible bond to keel bolts, no ground plate, VHF antenna highest point" and it goes on the pre-purchase survey report.

Findings to look for

Each page shows how the defect is found, what decides the grade and example findings written up at A, B and C.

ELECTRICAL

Lightning strike damage

How likely a boat is to be struck by lightning, where the damage hides, why the hull and through-hulls come first, what a surveyor checks after a strike and three example findings graded A, B and C.

How to find and write it up
UNDERWATER GEAR

Through-hull bonding

Why surveyors disagree on bonding through-hulls, what Nigel Calder and Don Casey advise, when a fitting should be bonded, what a surveyor checks and three example findings graded A, B and C.

How to find and write it up
ELECTRICAL

Stray current corrosion

How stray current corrosion shows up on a boat, why anodes can't stop it, where it comes from on board and at the marina, how it's tested and three example findings graded A, B and C.

How to find and write it up

Frequently asked

How are boats protected from lightning?

Florida Sea Grant's bulletin by Ewen Thomson explains that protection means minimising damage after a strike, since no accepted technique stops a strike. A protected boat has a continuous conducting path from the masthead to the water: an air terminal, down conductors, and grounding conductors in the water, plus bonding between large metal fittings.

How big should a lightning ground plate be on a boat?

Florida Sea Grant says that in salt water a single grounding conductor of a square foot or more is usually enough, and a lead keel connected through the keel bolts is adequate. Good Old Boat gives the same minimum of 1 square foot. Fresh water needs a much more extensive underwater grounding system.

Does a lightning protection system attract lightning?

Thomson's bulletin argues the chance of a strike doesn't depend on whether the boat is grounded. Florida surveyors' figures in it showed about 34% of the boats they surveyed for any reason had protection, against 29% of those surveyed after a strike.

Does lightning protection save the electronics?

Not reliably. In Thomson's sample of 71 struck boats, 96% suffered damage to at least some electronics. Protecting them takes transient suppressors at each piece of equipment and on antennas, twisted-pair wiring, and disconnecting gear ahead of a storm.

Your survey report, minutes after the sea trial

Dictate as you inspect. Axsail builds the findings and the report for your signature

Start free

More boat systems

All boat systems
ELECTRICAL AND PROTECTION

Battery not charging

Why a boat battery won't charge while running or on shore power: the voltages to expect, the alternator's fuses, relays and belt, the charger, and failed cells.

Read the checks
ENGINES AND FUEL

Outboard won't start

Why an outboard won't start and what to check in order: battery, neutral, kill switch lanyard, fuse, then fuel and spark when it turns over but won't fire.

Read the checks
ENGINES AND FUEL

Mercury outboard won't start

Why a Mercury outboard won't start or crank, from Mercury's troubleshooting chart: lanyard at RUN, neutral, the fuse, and priming after running dry.

Read the checks
ENGINES AND FUEL

Yamaha outboard won't start

Why a Yamaha outboard won't start, from Yamaha's own chart: neutral, the lanyard lock plate, choke, air vent screw, fuel, plugs and the 5-second crank rule.

Read the checks
ENGINES AND FUEL

Boat won't start

Why a boat won't start and what to check: battery switch, voltage and connections, neutral and kill switch, the starter if it clicks, fuel if it cranks.

Read the checks
ENGINES AND FUEL

Fuel gauge and sending unit

Why a boat fuel gauge stops working and how to test it: the gauge, the sender wire, the ground, and the 33 to 240 ohm sending unit, with each sender type.

Read the checks

Standards to check against

ABYC

American Boat and Yacht Council standards

What the American Boat and Yacht Council is, how its standards are written and kept up to date, why they're voluntary but still decide survey findings, how to get the full text, and the standards surveyors cite most.

What surveyors check

Report templates

FREE TEMPLATE · WORD

Pre-purchase survey

Free Word template for a recreational boat or yacht pre-purchase survey report: each section explained, with example wording and findings graded by urgency.

Open template
FREE TEMPLATE · WORD

Rig survey

A free Word template for a sailing yacht rig survey report: mast and spars, standing and running rigging, chainplates, furlers and rig age, with example findings graded A, B and C.

Open template