An outboard's shaft length has to match the boat's transom height. A short shaft is for a 15 inch transom, a long shaft for 20 inches, an extra long for 25 inches, and the biggest engines add 30 and 35 inch shafts. Suzuki and Honda publish a recommended transom height for each shaft code, in millimetres. Measure the boat's transom from the top to the bottom of the boat and pick the shaft listed for that height.
Shaft codes by maker
| Shaft | Transom height | Suzuki code | Honda code | Yamaha and Tohatsu |
|---|---|---|---|---|
| Short | 381 mm (15 in) | S | S | 15" |
| Long | 508 mm (20 in) | L | L | 20" (Yamaha L) |
| Extra long | 635 mm (25 in) | X | X | 25" (Yamaha X) |
| Extra extra long | 762 mm (30 in) | XX | U | 30" |
| Longest | 889 mm (35 in) | - | - | 35" (Yamaha V6 4.2L, V6 4.3L, XTO) |
Suzuki and Honda give the transom heights in millimetres. Yamaha and Tohatsu list shaft lengths in inches, and Yamaha's V MAX SHO 90 sheet spells out L as 20 inches and X as 25 inches. The 35 inch row is in inches only; the millimetres are a conversion. A few figures sit off the round numbers: Honda lists the BF60's L transom as 521 mm and the BFP60's as 531 mm and 658 mm.
Which shafts each power comes in
| Power | Usual shafts in the makers' current ranges |
|---|---|
| Up to 30 hp | 15" and 20"; some 9.9 and 15 to 20 hp portables also 25" (Honda BF8 to BF20, Tohatsu MFS6D and MFS9.9CY) |
| 40 to 60 hp | 15" and 20", and 25" on some (Suzuki DF60A, Honda BF50) |
| 70 to 150 hp | 20" and 25" |
| 175 to 300 hp | 20" or 25" and 30", with 35" on Yamaha's V6 4.2L F250 and F300 digital models |
| 350 hp and over | 25" and 30" (Honda BF350, Suzuki DF350AMD also 20"), with 35" on Yamaha's V6 4.3L and XTO |
How to measure transom height
ePropulsion, which makes outboards, describes it as the distance from the top of the boat's transom to the bottom of the boat. Measure straight down at the centre, where the engine clamps on. On a petrol outboard, ePropulsion says the shaft length itself runs from the top of the clamp bracket to the anti-ventilation plate, so a shaft that matches the transom puts the plate near the bottom of the hull.
Mounting height
Yamaha's owner's manual sets the anti-cavitation plate between the bottom of the boat and a level 25 mm (1 inch) below it. Mounted too high, it says, cavitation reduces propulsion and the propeller tips can cut the air, so the revs rise abnormally and the engine overheats. Mounted too low, water resistance rises and efficiency falls. Yamaha's performance bulletins record the mounting hole and the ventilation plate height against the boat bottom for every test boat, which is the setup the speed and fuel figures depend on.
For surveyors
Check the shaft code on the engine against the transom height you measure, and look at where the anti-ventilation plate sits relative to the keel line with the boat ashore. A long shaft on a 25 inch transom leaves the plate high and the engine prone to ventilate. With Axsail, say "transom 25 inches, engine L shaft, plate 4 inches above the hull bottom" and it goes into the engine survey report as a finding with the measurement.